What turbulence off your own roofline does to a home wind turbine

By Grace Lindqvist · September 7, 2026 · 8 min read
Wind turbines on a hillside
Photo by Alexander Mils on Unsplash

Stand on the downwind side of almost any two-storey house on a breezy day and you'll feel it: the air doesn't just slow down, it tumbles. I've done this test more times than I can count on our own place and on a neighbour's block up the valley, holding a cheap anemometer at head height and watching the reading jump around by three or four metres a second in the space of a few strides. That tumbling is turbulence, and it's the single most underestimated reason a home wind turbine that looked fine on paper produces a fraction of what the brochure promised.

I want to be specific about this because "siting matters" gets said a lot in wind circles without much explanation of the mechanism. Turbulence isn't just "less wind." It's structurally different air, and a small turbine handles it worse than a big one does.

What roofline turbulence actually is

When wind hits a building, it doesn't flow over it like water over a smooth rock. It separates at the eaves and ridge, forms a rolling vortex on the leeward side, and reattaches to smooth flow somewhere downstream, depending on the building's height and shape. Between the building and that reattachment point, the air is a mess: direction changes several times a second, speed swings wildly, and there's often a recirculating zone where the average wind speed is close to zero even though gusts still whip through. The rule of thumb used by the American Wind Energy Association and echoed in most siting guides is that this disturbed zone extends roughly twice the height of the obstruction downwind, and a similar distance upwind, with turbulence intensity elevated for a further distance beyond that. For a standard 6-8m eave house, that's a disturbed footprint extending 15-20 metres in the prevailing wind direction, sometimes more with a pitched roof adding effective height.

Trees do something similar but worse, because they're porous and seasonal. A stand of eucalypts that's bare-ish in one wind direction in winter becomes a solid wall of turbulence-generating canopy in spring. I've had neighbours site a turbine assuming a gum tree line was "mostly gaps" only to find the foliage density in full leaf changed the whole flow regime.

Why small turbines suffer more than large ones

This is the bit that doesn't get explained often enough. A large commercial turbine sits on a tower 80-120 metres tall, well above the turbulent boundary layer generated by ground obstructions, and its rotor is large enough that momentary gusts get averaged out across a huge swept area. A small residential turbine, by contrast, typically sits on a tower somewhere between 10 and 24 metres, with a rotor a couple of metres across. It's operating right in the zone where turbulence is worst, and its rotor is small enough that a single gust-and-lull cycle can dominate the whole power curve for that moment. Turbines also don't respond well to rapid direction changes. Most small horizontal-axis units use a tail vane or a yaw motor to track wind direction, and both have a response lag. In turbulent air the wind direction can shift 30-40 degrees in a couple of seconds; by the time the turbine has yawed to face it, the gust has often passed and the direction has shifted again. The turbine ends up chasing wind instead of catching it, and the energy loss from that mismatch doesn't show up on any brochure curve because those curves are measured in a wind tunnel with laminar, unidirectional flow. Real turbulence intensity in a built environment can run 25-40%, versus 10-15% on open, undisturbed rural land, and that difference alone can cut annual output by a third or more even when the average wind speed reading looks identical on paper.

The siting test I actually trust

Brochures love to talk about average wind speed. I care more about turbulence intensity, which is standard deviation of wind speed divided by mean wind speed over a set period. It's a genuinely useful number because it tells you how "clean" the air actually is, not just how fast it moves on average.

You don't need a professional meteorological mast to get a rough sense of this, though if you're spending real money on a turbine, a logged anemometer for a few months beats guesswork every time. What I do on a first pass is walk the block with a hand anemometer at the proposed hub height (or as close as I can get with an extension pole) at different times of day and different wind directions, and just watch how much the number jumps around second to second. If it's holding fairly steady with occasional gusts, that's a reasonably clean site. If it's swinging by half the average speed every few seconds, that's a turbulent one, and no amount of turbine quality fixes that. The formal guidance most installers and off-grid consultants use is the same rule I mentioned above: get your tower height at least as tall as any obstruction within 100-150 metres, plus enough extra height to clear the turbulent wake. That's part of why tower height matters more than turbine size in almost every real-world install I've seen. A cheap turbine on a tall, clean tower will consistently beat an expensive turbine stuck on a short tower in a turbulent wake.

Where this actually plays out on a real block

I helped a friend on Bellbird Track, about forty minutes from us, walk through a siting decision a couple of years back. Their instinct was to put the tower close to the house, near the existing power shed, because that minimises cable run and cost. The trouble was the shed sat directly downwind of the house in the prevailing south-westerly, in exactly the recirculation zone I've described. We moved the proposed tower base about 25 metres further out, clear of both the house wake and a line of wattles along the eastern boundary, and paid a bit more for underground cable run to get there. Was it worth it? I'd argue yes, and this is the one place I'll be blunt: I think a lot of installers undersell how much this decision matters because moving the tower further from the house adds cost and complexity to the quote, and it's an easier sale to just plant it near the shed. In my experience the honest ones will tell you straight that a turbulent site can cost you a third or more of your expected output, which dwarfs the extra trenching cost over the life of the system.

Reading a site plan before you commission a turbine

A few practical checks I now run on every siting conversation, whether it's my own gear or a mate's:

Check the prevailing wind direction properly, not from a general regional map but from local knowledge or, better, a few months of logged data. Coastal and valley sites in particular can have prevailing directions that differ meaningfully from what the nearest Bureau of Meteorology station fifteen kilometres away shows, because local topography channels airflow differently. Map every obstruction within 150 metres in the prevailing direction, not just the house. That includes the neighbour's shed, mature tree lines, and even large sheds or silos on adjoining rural land. Anything taller than about a third of your intended hub height in that radius is worth factoring in. Consider seasonal foliage change if there are deciduous or dense-canopy trees anywhere in the disturbed zone. A site that's clean in winter can turbulate badly once trees leaf out in spring, which matters if your load (say, water pumping or hot water heating) is seasonal too. And be honest about tower height budget before you get attached to a turbine model. This connects straight back to the setback question: our article on how far your turbine needs to sit from the house covers the distance side of this equation, but distance and height are really two variables in the same turbulence problem, not separate issues.

What this means for the economics

None of this is abstract engineering trivia. Turbulence intensity feeds directly into annual energy yield, and annual energy yield is the only number that actually matters for payback. If you've already read through what your energy bill actually tells you before you buy a home wind turbine, the honest next step is overlaying that consumption picture against a genuinely clean wind resource, not an averaged regional figure from a wind atlas. I'd also point out that turbulence is one of the few siting factors that's genuinely fixable after the fact, within limits. Adding tower height is expensive but possible. Relocating the tower further from the house before you pour a footing is nearly free by comparison. Waiting a season to log real turbulence data before committing capital is the cheapest option of all, and it's the one people skip most often because they're keen to get the thing up and spinning.

If you're weighing wind against other generation options for an off-grid or hybrid setup, it's worth reading how battery sizing changes when you're pairing wind and hydro rather than solar alone, since a turbulent, spiky wind resource has different storage implications than a smooth hydro flow or a predictable solar curve. The U.S. Department of Energy's WINDExchange programme and the Clean Energy Council's small wind guidance both cover turbulence and setback distances in more technical depth if you want to go further down this path before committing to a site.

Anyway, the shed on Bellbird Track has its turbine now, twenty-five metres further out than the original plan, on a tower two metres taller than first quoted. It's been running through two winters cleaner than the test readings at the old spot ever suggested it would. Sometimes the extra trench really is the whole project.

Tagged

Common questions

How do I know if my site has a turbulence problem without expensive equipment?
A cheap handheld anemometer will tell you a lot. Walk the proposed tower location at hub height (or as close as you can manage) across different wind directions and watch how much the reading jumps second to second. Large, rapid swings relative to the average speed indicate a turbulent site, even if the average speed itself looks reasonable.
Can I fix turbulence by just buying a more expensive turbine?
Not really. Turbulence is a siting problem, not a turbine quality problem. A premium turbine on a short tower in a turbulent wake will still underperform a modest turbine on a taller tower sited clear of obstructions. Height and distance from obstructions do more for output than the turbine model itself.
Does turbulence get worse or better with a taller house or two-storey extension?
Worse, generally. Taller buildings create a larger and more persistent wake because the disturbed zone scales roughly with obstruction height. If you're planning a home extension and a wind turbine on the same property, it's worth sequencing the wind siting assessment after any planned building changes, not before.
Is seasonal tree growth really significant enough to change turbine output?
Yes, more than most people expect. Deciduous trees or dense seasonal canopy can shift a site from relatively clean airflow in winter to meaningfully turbulent in spring and summer, which matters especially if your electricity demand (hot water, pumping) is also seasonal.
About the author
GL
Grace Lindqvist
Wind, hydro & off-grid · Colorado, US

Grace lives off-grid on a property with a micro-hydro system and writes about wind, hydro and the realities of generating your own power.

Off-grid homeowner; renewable-energy hobbyist.

More from Grace Lindqvist