Your battery's charge algorithm isn't optimised for your actual tariff
I had a Powerwall owner message me last month, genuinely confused, because his battery kept charging off the grid at 2pm on a mild autumn Tuesday — exactly when his time-of-use tariff was at its second-highest rate band. The battery wasn't broken. It was doing precisely what its default algorithm told it to do. The problem was that nobody had told the algorithm what his actual tariff looked like.
This is the gap I keep running into with battery-plus-solar systems, and it's a different problem to the sizing and reserve questions I've covered before. You can have the right capacity, the right C-rate, the right reserve setting for backup, and still lose real money every month because the charge-and-discharge logic running inside the inverter firmware is optimised for a generic tariff shape, not yours.
What "self-consumption mode" actually optimises for
Most hybrid inverters and battery management systems ship with a default mode often labelled something like "self-consumption" or "maximise self-use." In practice this mode is built around one assumption: that grid electricity is expensive and your solar is free, so the system should always try to charge from excess solar first and discharge whenever the house needs power, regardless of time of day.
That logic made sense a decade ago when most households were on flat tariffs. A kilowatt-hour from the grid at 7am cost the same as one at 7pm, so "always prefer the battery over the grid" was a reasonable default. The trouble is that flat tariffs are becoming rarer. Time-of-use pricing, demand tariffs, and in some regions genuinely negative wholesale pricing in the middle of the day have changed what "expensive" means — and the shape of that curve is different for every retailer, every network, and sometimes every postcode.
A battery running pure self-consumption logic on a time-of-use tariff will often do something counterintuitive: it discharges through the cheap overnight off-peak window just because the house is drawing a bit of load, then has nothing left when the expensive evening peak actually arrives. I wrote about this exact failure mode in why your battery drains before the evening peak even hits, but the root cause there is really a subset of this bigger issue: the algorithm doesn't know your tariff, so it can't plan around it.
The three tariff shapes that need different logic
I think about tariffs in three broad shapes, and each one needs a genuinely different charge strategy, not just a tweak.
Flat-rate tariffs are the simplest case. There's no time signal at all, so the only thing worth optimising for is maximising self-consumption and minimising any grid draw, full stop. Default settings are usually fine here.
Time-of-use tariffs with a defined peak window — common across a lot of the Australian east coast grids and plenty of US utility territories — need the battery to hold charge in reserve specifically for the peak window, even if that means drawing some grid power during a cheap shoulder period to top up solar shortfall. This is where generic self-consumption settings fail hardest, because the algorithm has no concept of "save this for later," only "use it now if the house needs it."
Tariffs with a negative or near-zero midday price, which are becoming more common as rooftop solar penetration rises on some networks, flip the logic again. Here you actually want the battery charging from the grid during the cheap midday window if your solar alone isn't filling it, because that's cheaper than waiting for afternoon solar that might get clipped by cloud. Few default algorithms are built to actively buy cheap grid power; most are built to avoid grid draw altogether.
Reading your own tariff before you touch a setting
Before you touch any app slider, pull up your actual retail plan and draw the 24-hour price curve on paper. I mean this literally — grab the tariff PDF, write down each time band and its rate, and sketch it. It takes ten minutes and most owners have never done it.
Once you can see the curve, compare it against your home's actual load curve, not the one you imagine you have. A smart meter portal or your retailer's app usually shows interval data. Overlay the two and you'll usually spot one of two things: either your peak load and the tariff's peak price band line up neatly (good, your battery just needs to be full going into that window), or they're offset by an hour or two, which is far more common than people expect, especially in households where evening cooking and air-con load happens later than the "peak" window the retailer defined years ago.
Export tariffs matter here too. If your feed-in rate is genuinely low or capped, discharging to self-use rather than letting solar export is almost always the better economic choice — which again argues against algorithms that treat exporting and self-consuming as equally fine outcomes. Export limits are already a drag on payback in a lot of installs; a mistuned charge algorithm compounds that by wasting cheap stored energy on low-value hours.
What manual scheduling can and can't fix
Most inverter manufacturers now offer a manual time-based scheduling override sitting alongside the default self-consumption mode. Fronius, SolarEdge, Tesla, and BYD all have some version of this in their apps, usually called something like "time-based control" or "TOU scheduling." This lets you force specific behaviour in specific windows: hold reserve above X% through peak hours, allow grid charging only in a defined cheap window, that sort of thing.
It helps a lot, and it's the single highest-value twenty minutes you can spend after installation. But manual scheduling has a real limitation: it's static. It doesn't adapt to variable solar output day to day, and it doesn't respond to dynamic wholesale pricing if your retailer offers a plan linked to the spot market. If your tariff changes seasonally — which a surprising number of time-of-use plans do, shifting peak windows between summer and winter — a schedule you set in July can quietly go stale by December.
This is where some systems now offer genuinely adaptive control, sometimes marketed as "smart" or "AI-optimised" charging, which pulls in forecast weather, your historical load pattern, and in some cases live wholesale price feeds to recalculate the plan daily. I'd treat these claims with a healthy dose of scepticism until you've seen a few weeks of logged behaviour, because the gap between what's spruiked in the sales brochure and what the firmware actually does in practice is often wider than installers admit.
Where virtual power plants change the calculation again
If you're enrolled in a virtual power plant programme, the charge algorithm question gets a third layer. VPP operators typically want the right to call on your battery's stored energy during grid stress events, which means the battery needs to hold a certain reserve at certain times regardless of what your own tariff curve says is optimal for you personally. Programmes like the NSW VPP Incentive are built around exactly this trade-off: you get a payment or bill credit for participation, but the system is no longer purely optimising for your household's tariff shape in isolation. It's a shared resource some of the time.
I'm enrolled in one myself, and I'll be honest, the first few months I found it mildly annoying watching the battery discharge into the grid at a moment I'd have preferred to keep the charge for my own evening load. The incentive payment made the arithmetic work out, but it's worth going in with eyes open about what control you're trading away, not just the headline dollar figure.
A practical sequence worth running once a year
I'd suggest doing this check annually, not just at install, because tariffs change and so does your household's load pattern — kids get older, you might add an EV, a work-from-home routine shifts your midday draw. First, re-pull your current tariff's time bands from your retailer's plan document, because these do get revised. Second, check your battery app's scheduling or time-of-use settings actually reflect those current bands, not whatever was configured at commissioning two years ago. Third, look at your export settings against your current feed-in rate, especially if you've recently added an EV charger that's changed your daytime load shape — I covered the collision between EV charging and self-consumption logic in this piece on why a battery can't do both well at once, and tariff mismatches make that conflict worse, not better.
If you're shopping for a new system and the installer can't clearly explain how the battery's charge logic handles your specific tariff — not battery chemistry in general, your plan specifically — that's a reasonable moment to ask more questions before signing. A unit like the Powerwall 3 or a BYD Battery-Box Premium HVS paired with a capable hybrid inverter such as the Fronius Symo GEN24 8.0 Plus can all do sophisticated time-based control, but only if someone actually configures it against your real tariff rather than leaving the factory default running.
Checking the numbers yourself
The Australian Energy Regulator and most state-based regulators publish comparison tools that show tariff structures in a standardised way, which is a useful sanity check against what your retailer's own portal shows you — retailer apps don't always surface the full time-of-use structure clearly. In the US, utilities publish their rate schedules directly, and NREL's PVWatts and related tools can help you model expected solar output against a given tariff shape if you want to go a layer deeper than the back-of-envelope sketch I described earlier.
None of this requires new hardware. It's a configuration problem, which is honestly the most fixable kind. I'd rather see a household spend an evening with their tariff PDF and their battery app than spend another few hundred dollars on capacity they don't need because the existing capacity is being used at the wrong hour.
— Declan Osei, Battery & EV Charging Writer, IceWarm
Common questions
- Will changing my battery's charge settings void the warranty?
- No, adjusting software settings like time-of-use scheduling or reserve percentages through the manufacturer's own app doesn't affect hardware warranty. Warranties cover cell degradation and defects, not configuration choices you make within the supported app.
- How often do time-of-use tariff bands actually change?
- It varies by retailer, but many time-of-use plans revise peak and off-peak windows at least once a year, and some shift seasonally between summer and winter. It's worth checking your plan document rather than assuming the bands set at install are still current.
- Can I run manual scheduling and self-consumption mode together?
- Most hybrid inverters let you set boundaries (like a minimum reserve through a peak window) while still defaulting to self-consumption logic outside those hours. It's a layered approach rather than an either/or choice, and it's usually the most practical setup for a typical household.
- Does a flat electricity tariff mean I don't need to worry about this at all?
- Largely, yes. If there's no time-of-day price signal, the default self-consumption algorithm is already optimising for the right thing. It's worth rechecking occasionally in case your retailer moves you onto a time-of-use plan without much fanfare.
Declan writes about home batteries, EV chargers and the emerging vehicle-to-grid category, drawing on his own multi-year EV ownership.
EV owner since 2019; home-charging enthusiast.
More from Declan Osei
- Why your solar panels and battery compete for the same sunny hoursYour panels, battery and household loads all want the same midday window. Here's why that overlap quietly shrinks the self-consumption gains you were promised.
- Your inverter's "smart mode" quietly decides self-consumption or backupMost hybrid inverters default to a mode that favours either self-consumption or backup reserve, not both. Here's how to check which one you're actually running.
- Sizing your home battery around C-rate, not just kWhBattery quotes sell you on kWh, but C-rate decides what your battery can actually deliver when you need it most. Here's why that number matters.
- Reserve settings vs backup sizing: why your battery doesn't do bothA battery set for maximum daily self-consumption often fails you in an outage. Here's why reserve settings and backup sizing pull in opposite directions.
- Why your battery's fire rating isn't the same as its install ratingA battery's cell safety rating and its approved installation location are two separate things. Here's why that gap trips up more installs than it should.
- Chemistry matters: LFP vs NMC batteries for home storageLFP and NMC home batteries aren't interchangeable. Here's what the chemistry actually changes for safety, lifespan and usable capacity.