Your inverter's "smart mode" quietly decides self-consumption or backup

By Declan Osei · November 17, 2026 · 8 min read
Electric vehicle charging cable connected to a car
Photo by Ernest Ojeh on Unsplash

I had a bloke message me last month, fairly annoyed, because his battery had sat at 19% all through a storm that knocked his street's power out for six hours. He'd paid for a battery specifically for backup. But the installer had left the inverter in a factory default mode tuned for maximum self-consumption, not for sitting full and waiting. Nobody had told him there was a choice to make, let alone which option they'd picked for him.

This happens more than most installers will admit. The hybrid inverter running your solar-plus-battery system has a setting, usually buried two or three menus deep, that decides whether the battery's job is to soak up every spare watt of solar during the day (self-consumption mode) or to hold a buffer against the chance the grid drops out (backup/reserve-weighted mode). These two jobs pull in different directions, and the inverter's "smart" algorithm, whatever the marketing material calls it, has to pick a lane. Most people never go looking for which lane it picked.

What self-consumption mode actually optimises for

In pure self-consumption mode, the inverter's logic is straightforward: charge the battery from excess solar as fast as the C-rate allows, discharge it as soon as the house draws more than the panels are producing, and treat the state of charge like a chequing account, not a savings account. The target is to get as close to zero grid import and zero wasted export as the battery's capacity allows on any given day.

That's the right mode if your main goal is bill reduction and your grid is reliable. It's also the mode almost every quote defaults to, because it's the mode that makes the payback numbers in the proposal look best. We've written before about how export limits quietly cap how much that payback actually delivers, and the self-consumption default compounds it: the battery will happily drain to near-empty most evenings, because nothing in its logic cares about tomorrow's blackout risk. It only cares about today's import bill.

What backup-weighted mode gives up to get reliability

Flip the priority to backup, and the inverter behaves completely differently. It'll stop discharging once state of charge hits a reserve floor, sometimes 20%, sometimes higher depending on the system and the install, and it'll hold that reserve even while you're paying peak import rates from the grid for everything above it. On paper that looks wasteful. In practice it's the whole point of having a battery that can actually do something useful during an outage.

The tension here is real and I don't think the industry explains it well. A battery held at a 30% reserve floor, as an example, effectively shrinks its own usable capacity for self-consumption by three days' worth of typical evening draw. If you want to understand why the number on your spec sheet was never the number you'd actually get to use even before backup reserve enters the picture, our piece on depth of discharge and usable capacity is worth reading alongside this one. Reserve settings stack on top of DoD limits, they don't replace them.

Why most installers pick one without asking you

I'll be honest: I think this is mostly a sales-process failure, not a technical one. The quoting software most installers use calculates projected savings assuming maximum self-consumption, because that's the number that closes the sale. Backup capability gets sold as a feature on the spec sheet, a tick box, rather than a mode that has to be actively configured and that trades off against the savings number the customer was shown.

We've covered this exact conflict from the reserve-sizing angle before, in reserve settings vs backup sizing, and it's worth reading if you haven't, because the two articles overlap but aren't the same question. That piece is about sizing math. This one is about which inverter mode is actually running on your system right now, today, regardless of how it was sized. You can have a perfectly sized battery for backup and still have it configured in a mode that ignores that sizing entirely.

A good installer will ask you, early, which scenario matters more: shaving the daily bill, or keeping the fridge and the modem alive during a grid event. A lot of installers don't ask. They set the default, hand over the app, and move on to the next job. If your installer didn't have that conversation with you, it's worth calling them back before you assume your system does what you think it does.

How to check what mode you're actually in

Open your inverter's monitoring app, not the glossy dashboard screen but the actual settings menu, and look for terms like "operating mode," "work mode," "self-consumption priority," or "backup reserve." Different brands label this differently and some bury it under "advanced settings" or a service-level menu that needs an installer login, which is itself a bit of a red flag for a feature this important.

Manufacturers that publish this clearly in their technical documentation make it easier to check for yourself. Tesla's support documentation for the Powerwall, for example, spells out the difference between its backup-only reserve and time-based control modes in plain terms, which is more than some competitors manage. If you're shopping and this matters to you, our Powerwall 3 and Battery-Box Premium HVS product pages both link through to manufacturer specs where you can compare how each handles reserve logic before you buy.

Once you've found the setting, the number to look for is the minimum state of charge the battery is allowed to discharge to under normal (non-outage) operation. If that number is low, single digits or low teens, you're running close to pure self-consumption. If it's sitting at 20% or above, someone has configured some backup buffer, intentionally or by factory default.

Why this isn't a "set and forget" decision

Here's the bit that surprises people: this setting should probably change with the seasons, and almost nobody adjusts it. During storm season, when outage risk is genuinely elevated, it makes sense to raise the reserve floor and accept slightly worse self-consumption economics for a few months. During a long, stable, sunny stretch, dropping the reserve back down recovers more of the daily savings the system was sold on.

I run my own home battery with a reserve that shifts manually twice a year, bumped up going into the storm season and dropped back down in the shoulder months when outages around here are rare. It's a five-minute job in the app. Most installers never mention you can do this, and most homeowners never think to ask, because the assumption going in is that the battery "just handles it." It doesn't. The algorithm handles whatever single priority it was told to optimise for, and that priority was almost certainly picked by someone else, on the day of install, without discussing it with you.

If your system also charges an EV, this gets more complicated again, not less. We've written separately about why a battery can't do self-consumption and EV charging well at once, and that same resource-contention problem applies to backup reserve too: a battery held back for an outage isn't available to top up the car overnight, and a battery flat out optimising for EV charging isn't holding anything in reserve for the grid going down.

Matching the mode to how you actually use the house

The honest answer to "which mode should I run" depends on things no inverter algorithm can know: whether you're on bottled oxygen, whether you work from home and need the internet up, whether your area has copped three outages this year or none in the last five. The Australian Energy Market Operator and individual network operators publish reliability data by region, and it's worth a quick look before you decide this is a "set it and forget it" toggle rather than something tied to your actual risk.

My own view, and I'll flag this as opinion rather than settled fact: I think most suburban installs with a reasonably reliable grid are over-provisioned for backup and under-provisioned for genuine self-consumption savings, because backup sounds better in a sales pitch than "it'll shave 40 cents off your evening peak." If your grid is genuinely flaky, that calculus flips, and a higher reserve floor earns its keep. There's no universal right answer here, just a setting that somebody chose for you and that you're allowed to change.

Checking the app is worth the ten minutes

Go and check it this week, is my advice. Open the app, find the mode, find the reserve percentage, and ask yourself honestly whether that number matches what you thought you were buying. If you bought a battery for blackout protection and it's sitting at a 5% floor, that's a conversation with your installer, not a technical mystery. If you bought it purely to cut your bill and it's holding 40% in reserve every single day regardless of outage risk, you're leaving savings on the table for a scenario that may happen once every few years.

The gap between what a battery is configured to do and what the owner believes it's doing is, in my experience, one of the more common and most fixable problems in residential storage. It costs nothing to check. It costs a bit of annoyance to discover six months in, mid-outage, that the fridge went off anyway.

Tagged

Common questions

Can I run self-consumption and backup reserve at the same time?
Not fully. Most hybrid inverters let you set a minimum reserve floor below which the battery won't discharge, which gives you a partial backup buffer while still allowing self-consumption above that floor. But the floor itself is a trade-off: every percentage point held back for backup is a percentage point unavailable for daily bill savings.
Does changing the mode void my battery warranty?
Generally no, adjusting the operating mode or reserve percentage through the manufacturer's own app is a normal user setting, not a modification that affects warranty. If you're unsure, check the specific terms for your battery model or ask your installer, since this can vary by brand.
How do I know what reserve percentage I actually need for backup?
It depends on your outage history and what loads you want to keep running. A rough approach is to estimate your essential overnight load (fridge, modem, a few lights) in kWh and make sure the reserve floor covers at least one evening of that before the sun comes up again. Our piece on reserve settings vs backup sizing goes into this in more detail.
Will my installer change this setting for me if I ask?
Most can, either remotely through the monitoring platform or by walking you through it over the phone. If they're reluctant or say it can't be changed, that's worth pushing back on, since nearly every hybrid inverter on the market exposes this as a user or installer-level setting.
About the author
DO
Declan Osei
Battery & EV charging · Brisbane, AU

Declan writes about home batteries, EV chargers and the emerging vehicle-to-grid category, drawing on his own multi-year EV ownership.

EV owner since 2019; home-charging enthusiast.

More from Declan Osei