Depth of discharge: why your battery's usable kWh isn't the number on the box

By Declan Osei · September 13, 2026 · 7 min read
Electric vehicle charging cable connected to a car
Photo by Ernest Ojeh on Unsplash

A reader emailed me last month asking why his newly installed 13.5kWh battery only ever seemed to give him about 12kWh before the app flagged it as empty. He wasn't being ripped off. He'd just never been told what depth of discharge actually means, and to be fair, most installers gloss over it in the sales pitch because the headline number sells better than the honest one.

I've run an EV and a home battery system for years now, and the gap between "rated capacity" and "what you actually get to use" is one of those details that quietly determines whether your sizing maths works out. Get it wrong and you'll buy a battery that's a size too small for what you actually need, or pay for capacity you'll never see.

What depth of discharge actually is

Depth of discharge, usually shortened to DoD, is the percentage of a battery's total capacity you're allowed to draw down before the system stops discharging to protect the cells. A battery with a 90% DoD rating and a 10kWh nominal capacity gives you 9kWh of usable energy. The remaining 10% sits there as a buffer the battery management system won't let you touch.

This isn't a manufacturing defect or a marketing trick, though it can feel that way when you're staring at an app telling you your "10kWh" battery just hit empty at 9.1kWh used. It's a deliberate electrochemical decision. Lithium-ion cells, whether LFP or NMC, degrade faster when they're driven to full charge or fully flat repeatedly. Manufacturers build in headroom at both ends of the state-of-charge curve specifically to slow that degradation and protect the warranty they're offering.

Most residential LFP batteries on the market today are rated somewhere around 90 to 100% usable DoD, because LFP chemistry tolerates full cycling better than NMC. Older NMC-based systems were sometimes rated closer to 80 to 90% for exactly that reason. It's worth checking the datasheet rather than assuming, because I've seen the usable-versus-nominal gap vary by more than a full kilowatt-hour between two batteries that looked identical on a glossy brochure.

Why the spec sheet number and your app never quite match

Here's where it gets murkier. Even the "usable" figure on a spec sheet is measured under lab conditions: a fresh battery, a controlled temperature, a specific charge and discharge rate. Your garage in January, or your side return in a Brisbane summer, is not a lab. Inverter conversion losses, cabling resistance, and the battery management system's own conservative buffering all shave a bit more off in the real world.

On my own system I generally see 4 to 8% less usable energy on a typical night than the datasheet DoD would suggest, and that's on a system installed correctly with decent cable runs. I'd argue anyone who quotes you usable capacity as a precise deliverable number, rather than a reasonable range, hasn't actually metered a system through a full year of Australian seasonal swings.

There's also a slow drift as the battery ages. Every lithium battery loses a small percentage of total capacity per year, and that loss compounds with the DoD limit rather than replacing it. A battery that started at 90% usable DoD on a 13.5kWh nominal pack, after five years of typical degradation, might be delivering closer to 11kWh on a good night rather than the 12.15kWh you calculated on day one. This is a separate conversation from DoD but they interact, and most sizing conversations at the point of sale ignore both.

Why this actually matters for sizing, not just trivia

If you're sizing a battery for self-consumption versus backup, DoD changes the maths in different ways depending on the job. For self-consumption, a few percent either way barely registers, because you're topping the battery up and drawing it down daily and the shortfall just shows up as slightly more grid import on a cloudy stretch. Annoying, marginal, not dangerous to your plan.

For backup sizing it's a different story. If you're calculating "how many hours will this battery run my fridge, lights and modem during an outage," and you've done that maths on the nameplate capacity rather than the usable figure, you can end up 10 to 15% short on runtime right when it matters. I know a couple in Torquay who sized their backup around a rated 10kWh figure for exactly this reason, and during a storm outage last winter their system tripped over two hours earlier than they'd planned for. Not catastrophic, but it meant the chest freezer wasn't covered as long as they'd assumed.

The fix is straightforward once you know to ask for it: get the installer to quote usable kWh, not nameplate kWh, and build your backup hours calculation off that number, then shave a further 5 to 10% buffer off for real-world losses and future degradation. It's not complicated maths, it's just a step most quotes skip because the bigger number looks better on paper.

The manufacturer's fine print on DoD is not always consistent

One frustration I have with this corner of the industry: there's no single universal standard for how DoD is disclosed. Some manufacturers publish nominal capacity and usable capacity as two clearly separate figures. Others bury the usable figure in a footnote or a separate technical document you have to specifically ask for. The Clean Energy Council's approved product list is a reasonable starting point for checking which batteries have gone through independent verification in Australia, and I'd treat any installer who can't immediately produce both figures on request as a mild red flag, not a dealbreaker, but a prompt to ask more questions.

In the US, similar variability exists across manufacturer datasheets, and the Department of Energy's guidance on residential storage system specifications is a decent reference point if you want to compare disclosure standards across brands. Neither country has forced a single consistent labelling convention yet, which is honestly overdue given how much this number affects real household planning.

How this plays into chemistry and warranty terms

DoD rating and cycle life warranty are linked, and manufacturers set both together based on how hard they're willing to let you push the chemistry before the warranty clock effectively runs faster than advertised. A battery rated for a higher DoD generally comes from a chemistry, almost always LFP these days, that's more tolerant of full cycling without accelerated capacity fade. That's covered in more depth in our piece on LFP versus NMC chemistry, but the short version relevant here is that a battery advertised with a high usable DoD and a long cycle warranty is telling you something real about how the manufacturer expects the cells to behave over a decade, not just marketing puffery.

Worth noting too that some installers set a slightly more conservative discharge floor than the manufacturer's rated DoD, as part of how they configure the charge and discharge windows during commissioning. This is usually a sensible move for longevity, but it means your actual daily usable capacity might sit a notch below even the manufacturer's usable DoD figure, by design. Ask your installer what floor they've set and why.

What I'd actually do differently if quoting this again

If I were resizing my own system today, I'd ask for three numbers from any installer before signing anything: nameplate capacity, manufacturer-rated usable capacity accounting for DoD, and the installer's configured floor after commissioning. Three numbers, not one glossy headline figure. It takes five minutes of conversation and it's the difference between a backup plan that actually covers your outage window and one that quietly runs short two hours before dawn.

None of this is a reason to distrust battery storage generally, current LFP chemistry is genuinely solid and the DoD buffers exist for good reasons tied to cell longevity. It's just a reason to read the second page of the datasheet rather than the marketing summary on the first. If you're still weighing up whether a battery makes sense for your house at all, our decision framework is a reasonable place to start before you get into capacity specifics, and our Powerwall 3 and Battery-Box Premium HVS product pages both list usable capacity separately from nameplate, which is exactly the kind of disclosure you should be looking for elsewhere too.

Check the fine print, ask for the three numbers, and size your backup hours off the smallest one you're given, not the biggest one you're sold.

Tagged

Common questions

Is a lower depth of discharge rating a sign of a worse battery?
Not necessarily. It usually reflects an older or different chemistry, typically NMC rather than LFP, that's more sensitive to full cycling. Pair the DoD figure with the cycle life warranty to get the full picture rather than judging DoD alone.
Does depth of discharge change as the battery ages?
The DoD percentage itself generally stays fixed by the battery management system, but the total capacity it's a percentage of shrinks slowly each year through normal degradation, so the actual kWh you get on a given night drops gradually over the system's life.
Should I size my backup battery on nameplate or usable capacity?
Always use usable capacity, and ideally shave a further 5 to 10% off that for real-world losses and future degradation, particularly if you're calculating exact backup runtime hours for essential circuits.
Can I change the discharge floor an installer sets during commissioning?
Often yes, within the limits the manufacturer allows, though a more conservative floor is usually better for long-term battery health. Ask your installer to explain the trade-off before requesting a change.
About the author
DO
Declan Osei
Battery & EV charging · Brisbane, AU

Declan writes about home batteries, EV chargers and the emerging vehicle-to-grid category, drawing on his own multi-year EV ownership.

EV owner since 2019; home-charging enthusiast.

More from Declan Osei