The defrost cycle myth: that "cold blast" doesn't mean your heat pump failed
I got a call from a client in Orange a few winters back, convinced her new ducted system was "broken" because it kept spitting cold air for a few minutes every hour or so. She'd stood in the hallway with her coat on, timing it. It wasn't broken. It was doing exactly what it's designed to do on a frosty morning, and nobody had told her what to expect before she signed the contract.
This is one of the most common calls installers get in the first cold snap of the season, and it's almost never a fault. It's the defrost cycle, and if you own or are about to buy a heat pump in a climate that dips near or below freezing, understanding it will save you a service callout fee and a fair bit of anxiety.
What's actually happening during defrost
An air-source heat pump pulls heat out of outdoor air, even cold air, by running it across an outdoor coil filled with cold refrigerant. When the outdoor temperature drops toward freezing and there's moisture in the air, that coil gets cold enough that frost starts building up on its fins, the same way frost forms on a car windscreen overnight.
A thin layer of frost is fine. A thick layer is a problem, because it blocks airflow across the coil and the system's ability to extract heat collapses. So the unit needs to periodically melt that frost off. It does this by reversing the refrigeration cycle for a few minutes, running like an air conditioner in reverse, which pumps heat into the outdoor coil to melt the ice rather than into your house.
That's the bit that confuses people. For those two to ten minutes, the indoor unit is briefly not delivering heat, and depending on the system, it might blow noticeably cool air, or the fan might pause entirely while the compressor handles the reversal. Most modern systems try to minimise the felt effect, some hold the indoor fan off during defrost specifically so you don't get a blast of cold air, but not all of them do, and older or cheaper units are more likely to just push through it.
How the system knows when to defrost
This isn't done on a dumb timer, or at least it shouldn't be on a properly designed system. Better controllers use a combination of outdoor coil temperature sensors and either a timer-and-temperature hybrid or, on more sophisticated units, an actual measurement of airflow restriction or refrigerant pressure differential to decide frost has built up enough to warrant a cycle. This is one of the genuine differences between a budget system and a properly cold-climate-rated one, and it's a big part of what separates the marketing claim from the guarantee, something I've gone through in more detail in what "cold-climate rated" on a spec sheet actually guarantees.
A well-tuned defrost algorithm should call fewer, better-timed cycles. A poorly tuned one, or a system that's undersized and running flat out constantly, will defrost more often and for longer, because it's spending more time at the coil temperatures where frost forms fastest. If your system seems to be defrosting every fifteen minutes rather than every hour or so, that's worth a service call, but the fix is diagnostic, not "the heat pump doesn't work in the cold."
Why some systems handle it worse than others
I'll say something a bit unpopular here: a lot of the "heat pumps struggle in the cold" complaints I hear are really "this particular installation was under-specified for the climate" complaints wearing a different hat. The refrigeration cycle physics behind defrost is the same everywhere. What changes is how much margin the system has to spare while it's not heating.
If a heat pump is sized correctly with headroom at the design temperature, a short defrost cycle is a minor blip, the house's thermal mass carries it through and nobody notices. If the system is already running near its maximum output just to keep up, that same defrost cycle creates a noticeable dip in comfort because there was no spare capacity to draw on. This is exactly the scenario I described in the design temperature mistake that's quietly costing heat pump owners — undersizing for your climate zone doesn't just show up as slow warm-up, it shows up as every defrost cycle feeling like the heating's cut out.
The reverse is also true. An oversized system short-cycles more, which as I've written about in why oversizing quietly ruins comfort and running costs, brings its own set of problems, though defrost frequency isn't usually the headline issue there.
Where I see this go wrong in real installs
The properties I get called to most often for "my heat pump doesn't work below freezing" complaints share a pattern: coastal Victorian or Tasmanian sites, or high-altitude NSW towns, where humidity sits high and temperatures hover right around zero for long stretches. That's the worst-case band for frost formation, colder air actually holds less moisture so deep-winter frost can be less of an issue than the marginal zone just above freezing.
On one job on a street just off the main road through Blackheath in the Blue Mountains, the homeowner had a perfectly good mid-tier system that was defrosting constantly through winter mornings because the outdoor unit was mounted in a low corner of the yard where cold air pooled and airflow was partially blocked by a side fence. The unit itself wasn't the problem. Siting was. We're back to the same lesson that shows up with wind turbines and even solar shading, mechanical equipment performs on paper and underperforms in the specific microclimate of your yard.
In the US, the equivalent complaint tends to come from the upper Midwest and New England, where cold-climate-rated heat pumps handle the deep cold reasonably well but the shoulder-season freeze-thaw cycles still trigger frequent defrost. NEEP's cold-climate air-source heat pump product list, maintained by the Northeast Energy Efficiency Partnerships, is a genuinely useful reference if you're trying to compare how different models are rated for exactly this kind of performance at low ambient temperatures.
What normal defrost actually looks and sounds like
Worth knowing the signs so you can tell normal from actually-broken. A normal defrost cycle: the outdoor fan stops, you might hear a whooshing or hissing sound as refrigerant flow reverses, steam or visible water vapour may rise off the outdoor unit as ice melts, and the cycle wraps up in under ten minutes before the system returns to normal heating. Water dripping from the outdoor unit afterwards is expected, that's the melted frost draining away, not a leak.
What's not normal: defrost cycles running longer than fifteen minutes, ice that doesn't fully clear and builds up cycle after cycle, or the outdoor unit staying iced over even hours after a defrost should have finished. That pattern usually points to a failed defrost sensor, a stuck reversing valve, or a genuinely undersized or badly sited unit that can't generate enough heat during the reverse cycle to actually clear the ice it built up.
I'd also flag that a system defrosting constantly on a day that isn't actually that cold, say, a mild 8°C morning, is a red flag worth calling your installer about rather than waiting out. That's not typical physics, that's usually a sensor fault or a refrigerant charge issue, and it's the kind of thing that should have been caught at commissioning if it had been done properly.
What to check before you buy, and what to ask your installer
If you're heat-pump shopping for a climate that regularly sits near freezing in winter, ask specifically about defrost performance, not just the headline COP number. Ask what the low-ambient capacity retention looks like on the spec sheet, most manufacturers publish a capacity curve showing output at several outdoor temperatures, and a steep drop-off near 0°C to 2°C tells you defrost cycling is likely to be more aggressive. ENERGY STAR's cold-climate heat pump specification is a solid independent benchmark if you want a baseline that isn't just manufacturer marketing copy.
Ask, too, whether the indoor unit suppresses fan operation during defrost, this is a genuine comfort difference between models and not something that shows up on a standard spec sheet. And ask your installer directly how they've accounted for your specific outdoor unit siting, sheltered from prevailing wind, elevated off the ground, clear of fences that trap cold air pooling. It's a five-minute conversation that avoids a callout six months later for something that was never actually broken.
For anyone weighing ducted versus a split system for a colder climate, siting and defrost behaviour is one more factor worth folding into that decision, which I cover more broadly in ducted vs split-system heat pumps.
Common questions
- Is it normal for my heat pump to blow cold air for a few minutes in winter?
- Yes, this is almost always a defrost cycle, where the system briefly reverses to melt ice off the outdoor coil. It typically lasts two to ten minutes and happens more often when outdoor temperatures hover right around freezing with high humidity.
- How often should a heat pump defrost in winter?
- There's no universal number, it depends on outdoor temperature, humidity and your specific unit's defrost control logic, but a well-sized, well-sited system in typical near-freezing conditions might defrost every 30 to 90 minutes. Cycles happening every 10-15 minutes suggest an undersizing, siting or sensor problem worth a service call.
- Does frequent defrosting mean my heat pump is undersized?
- Not always, but it's one of the more common causes. An undersized system runs closer to its capacity limit for longer stretches, which pushes coil temperatures into the frost-forming range more often. Poor outdoor unit siting, cold air pooling, blocked airflow, is another frequent culprit.
- Can I stop my heat pump from defrosting so often?
- You can't and shouldn't disable defrost, it protects the system, but you can address the root cause. Check outdoor unit siting for airflow blockages, confirm the system was sized correctly for your climate's design temperature, and if cycles seem excessive for the actual outdoor conditions, get the refrigerant charge and defrost sensor checked by a licensed technician.
Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.
Mechanical engineering background; ex-HVAC design.
More from Priya Nathan
- Why two identical heat pumps can sound totally different next doorSame unit, same decibel rating, wildly different noise complaints. The myth isn't the spec, it's where and how the outdoor unit gets placed.
- The design temperature mistake that skews every heat pump quoteMost heat pump quotes size off the wrong outdoor temperature. Here's why design temperature, not average winter temp, decides if your system actually keeps up.
- The humidity myth that throws off heat pump cooling estimatesHeat pump cooling quotes focus on temperature drop, but humidity removal is the part that actually decides comfort and running cost.
- Why "heat pumps don't work in the cold" is the wrong myth to worry aboutHeat pumps do work in the cold. The real myth is believing minimum operating temperature is the number that matters for your install.
- Vetting a refrigerant handling licence before heat pump work startsBefore a heat pump installer touches refrigerant lines, check their handling licence. Here's what the card actually proves and what it doesn't.
- Why a return-on-investment number for a heat pump rarely survives real lifeMost heat pump payback calculations use one winter's gas price and a brochure COP. Here's why the real payback period almost never matches the quote.