Why two identical heat pumps can sound totally different next door

By Priya Nathan · November 21, 2026 · 7 min read
Outdoor heat pump unit installation
Photo by alpha innotec on Unsplash

I had a call last month from a reader in Ocean Grove who'd bought the exact same ducted system as his neighbour two doors down on Hodgson Street. Same brand, same model, same published sound rating. His neighbour says you can barely hear it running. He says it hums through his bedroom wall at night and he's losing sleep over it. Nobody lied to him. Nobody swapped the unit. The spec sheet was accurate the whole time.

This is the bit of the heat pump noise conversation that almost never gets covered, because everyone's busy arguing about the decibel number itself. I've already written about why the "quiet" rating on the box doesn't mean quiet in your backyard — that's a measurement problem, tested in an anechoic chamber at a fixed distance with nothing nearby to reflect sound back at you. But there's a second myth sitting right behind it, and it's arguably bigger: the idea that two identical units will sound the same because they're identical units. They won't. Siting changes the experienced noise more than almost any spec on the page, and most quotes don't treat siting as an engineering decision at all. It's treated as "wherever the pipe run is shortest."

The physics nobody puts in the quote

Sound doesn't travel in a vacuum from the unit to your ear. It bounces. A compressor sitting in open space, away from walls, loses energy as it radiates outward in all directions. The same compressor tucked into a corner formed by a besser-block fence and a rendered wall gets reinforced — the hard surfaces reflect sound back toward the gap instead of letting it dissipate, and if that corner happens to face a bedroom window, you've built yourself a little amplifier without meaning to.

I'd argue this is the single most under-engineered part of a typical install. Installers size the unit against the design temperature, they check the circuit, they measure the pipe run — all things I've covered elsewhere on this site — and then the outdoor unit gets bolted onto whichever concrete pad happens to already exist, because that's the path of least resistance on install day. Nobody walks the boundary and asks where the reflected sound actually ends up.

Distance matters less than direction

Here's the part that trips people up: sound pressure does fall off with distance, roughly following the inverse square law in open air, so doubling the distance from the unit theoretically drops perceived loudness noticeably. But that only holds in open, unobstructed conditions. Once you introduce a fence line, a side-return alley, or a gap between two houses — which is exactly where most outdoor units end up on narrow suburban and US tract-home blocks — the geometry starts to matter more than the raw metres.

A unit sited three metres away but firing straight down a tight side-return between two houses can be louder at a bedroom window than a unit five metres away in open yard, simply because the side-return channels the sound instead of letting it spread. I've seen this on a renovation near Mountjoy Parade in Lorne, where the client's new unit went into a narrow gap beside the garage — technically close to the shortest pipe run, technically compliant on paper, and audibly louder in the main bedroom than the old wall-mounted split it replaced, which had been sited in the open backyard.

What councils and standards actually regulate (and what they don't)

In Australia, most states apply noise limits to fixed plant like heat pump outdoor units through state EPA policies, and the relevant standard most acousticians reference is AS 1055 for environmental noise assessment, with compliance usually assessed at the boundary of the nearest affected property, not at your own bedroom window. That's a meaningful gap. A unit can comfortably pass a boundary noise test and still be an annoyance for the person who sleeps twelve feet from it inside their own house, because the regulation was never written to protect you from your own appliance — it protects your neighbour from it.

In the US, there's no single national noise code for residential HVAC; it falls to local zoning and noise ordinances, which vary enormously between a county in Arizona and a town in Massachusetts. The manufacturer's published sound rating, listed in accordance with AHRI testing standards, is a useful comparison tool between models but it was never designed to predict what you'll hear at your specific window, at your specific distance, against your specific fence.

This is worth sitting with for a second: the compliance test and the lived experience are answering two different questions. One asks "does this bother the neighbours." The other asks "can I sleep." A unit can pass the first and fail the second.

The checklist an installer should walk through, but often doesn't

A proper siting assessment looks at more than a tape measure to the nearest wall. It considers which rooms the unit faces and when those rooms are occupied — a laundry doesn't care about compressor hum at 11pm, a bedroom does. It considers the reflective surfaces nearby: rendered masonry, colorbond fencing and glass all bounce sound harder than timber paling or a garden bed. It considers prevailing wind direction, because sound carries further downwind. And it considers vibration transmission through the mounting pad into the structure of the house itself, which is a separate problem from airborne noise and needs anti-vibration mounts or a properly isolated slab, not just a concrete pad poured flush against the wall.

None of this is exotic engineering. It's the kind of thing a ducted system like the Zuba Central or a Daikin Premium Inverter Ducted install should factor into the quote stage, before the pad gets poured, because moving an outdoor unit after installation is a much bigger job than specifying the right spot the first time. I've started asking installers directly: have you stood where my bedroom window is and looked back at where you're proposing to put this. Most haven't been asked that before. A few get visibly uncomfortable, which tells you something.

Fixes that actually work, and ones that don't

Acoustic fencing or a baffle wall between the unit and the affected window can help, but only if it's tall enough and close enough to the source to interrupt the direct line of sound — a token lattice screen does almost nothing. Increasing distance helps, genuinely, but only in open conditions; cramming the unit further down the same tight side-return just moves the amplifier a metre over. Anti-vibration mounts address the structure-borne component, which matters a lot if your bedroom wall is the same wall the unit sits against, but they do nothing for the airborne noise travelling through the window.

The fix most people skip because it costs more upfront: paying an installer to actually site the unit based on where the noise will land, not where the pipe run is shortest. On a retrofit this sometimes means a slightly longer refrigerant line, which is a real cost worth weighing against years of disturbed sleep. It's a trade-off I'd rather see made deliberately than by default.

What I tell readers before they sign

Ask for the proposed outdoor unit location marked on a site plan, not just a verbal "round the side." Ask what's on the other side of that wall or fence, and whether it's your bedroom or theirs. Ask whether the installer has run an acoustic assessment referencing AS 1055 in Australia, or checked the relevant local noise ordinance in the US — not because you expect a formal report for a residential job, but because the question tells you whether siting was considered at all. If your installer's answer is some version of "it'll be fine, they're all pretty quiet now," that's not an answer, it's an assumption resting on the decibel number on the box, which, as I've written before, doesn't travel with the unit into your actual backyard.

Get the siting right and a correctly sized heat pump is genuinely unobtrusive — most reasonably sited inverter systems settle into background noise within a few metres. Get it wrong and you end up with my reader on Hodgson Street: identical hardware, identical rating, completely different outcome, and a neighbour two doors down who has no idea what the fuss is about.

For the broader sizing and running-cost side of getting a heat pump install right, our heat pumps hub covers design temperature, capacity derating and the other quote-stage traps worth checking before you sign anything.

Tagged

Common questions

If two heat pumps have the same decibel rating, should they sound the same?
Only in identical conditions, which almost never happens in real installs. The published rating is measured in controlled, open conditions at a set distance. Once you introduce a fence, a corner, a side-return alley or a hard rendered wall nearby, reflected sound changes what you actually hear, sometimes significantly, even with an identical unit.
Does moving the outdoor unit further from the house always reduce noise?
Distance helps in open, unobstructed space, but it's not the whole story. A unit sited closer in an open yard can be quieter at your window than one sited further away but tucked into a tight gap between buildings, because the gap channels and reinforces the sound instead of letting it dissipate.
What should I ask an installer about noise before signing a heat pump quote?
Ask them to mark the proposed outdoor unit location on a site plan, confirm what room is on the other side of the nearest wall or fence, and explain how they accounted for reflective surfaces and the room's typical occupied hours. If they can't answer, siting probably wasn't considered.
Do noise regulations protect me from my own heat pump's noise?
Generally no. In Australia, state noise policies and the AS 1055 reference framework are typically assessed at the boundary of a neighbouring property, protecting neighbours rather than the owner of the unit. In the US it depends on local zoning and noise ordinances, which vary by council or county.
About the author
PN
Priya Nathan
Heat pumps & HVAC · Melbourne, AU

Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.

Mechanical engineering background; ex-HVAC design.

More from Priya Nathan