How Heat Pumps Actually Work (and Why That Makes Them So Efficient)

By Priya Nathan · July 18, 2026 · 4 min read
Outdoor heat pump unit mounted on a brick wall
Photo by alpha innotec on Unsplash

If you take one thing away from this site, make it this: a heat pump does not generate heat. It moves it. That single idea explains almost everything about why heat pumps are efficient, how they can heat a home in winter and cool it in summer with the same hardware, and why they're the centrepiece of home electrification.

The refrigeration cycle, run in either direction

Every heat pump — and every refrigerator, and every air conditioner — works on the same refrigeration cycle. A refrigerant fluid is compressed, which raises its pressure and temperature, then passed through a coil where it releases that heat to the surrounding air (or water). It's then allowed to expand and cool, passed through a second coil where it absorbs heat from wherever it is now colder than its surroundings, and the cycle repeats.

A refrigerator uses this cycle to pump heat out of a cold box into your warmer kitchen. An air conditioner pumps heat out of a cool room into hotter outside air. A heating heat pump does the reverse: it pumps heat out of cold outside air (yes, even air well below freezing still contains extractable heat) into your warmer home. A reversible heat pump just has a valve that swaps which coil is the "inside" one, so the same box heats in winter and cools in summer.

Why "moving" beats "making"

A resistive electric heater — a bar heater, a fan heater, an electric water heater element — converts electrical energy directly into heat. At best, that's a 1-for-1 conversion: one unit of electricity in, one unit of heat out. That's already 100% efficient in a thermodynamic sense, but it's the ceiling.

A heat pump isn't creating that heat from the electricity at all — the electricity only runs the compressor and fans. The heat itself is coming from outside air (or ground, or water) essentially for free. So instead of a 1:1 ratio, a well-specified heat pump typically moves 3 to 5 units of heat energy for every 1 unit of electrical energy it consumes. That ratio is called the Coefficient of Performance (COP) for heating, or is expressed as HSPF/SEER-style seasonal ratings in the US and star ratings in Australia. It's the reason heat pump running costs are consistently lower than gas or resistive electric heating, even before you factor in what's happening to gas prices.

What changes performance

The colder the outside air, the harder the compressor has to work to extract usable heat from it, so COP drops as outdoor temperature drops — this is why sizing and cold-climate-rated equipment matter more in genuinely cold regions (much of the US Midwest and Northeast, and the Australian alps and Tasmania) than in temperate coastal Australia. Manufacturers publish COP or HSPF curves across a range of outdoor temperatures; a unit rated well for a Melbourne winter is not automatically rated well for a Minnesota one.

Beyond space heating: hot water too

A hot-water heat pump applies exactly the same principle to your hot water cylinder instead of your living room — it extracts heat from the surrounding air and concentrates it into the water tank, instead of using a resistive element or a gas burner. For most households, replacing a gas or electric-resistance hot water system with a heat pump hot water system is one of the single highest-return electrification upgrades available, because hot water is a large, steady, easy-to-measure load.

The bottom line

Once you see a heat pump as "a fridge running in reverse" rather than "a fancy heater," the rest of the buying decision gets easier: what matters is the unit's efficiency curve at your climate's actual temperatures, correct sizing for your home's heat loss (oversizing is a common and costly mistake), and — where relevant — whether it's ducted, split-system, or a dedicated hot-water unit. We cover all three in the rest of this pillar.

Tagged
About the author
PN
Priya Nathan
Heat pumps & HVAC · Melbourne, AU

Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.

Mechanical engineering background; ex-HVAC design.

More from Priya Nathan