How to Vet a Heat Pump Installer: Licensing, Sizing Method and Red Flags

By Priya Nathan · July 16, 2026 · 6 min read
Electrician installing wiring on site
Photo by Emmanuel Ikwuegbu on Unsplash

I ask every prospective installer one question before anything else: how do you size the system for a specific house. If the answer is some version of "we go off square metres," that's already telling me something. This is editorial guidance on what to look for. We don't operate as a directory or referral service, and we don't list specific businesses.

Licensing and refrigerant handling

In Australia, anyone handling refrigerant needs a refrigerant handling licence issued under the relevant Australian Refrigeration Council scheme, on top of any electrical licensing for the associated wiring work. Ask specifically about both, since installing a split system involves handling refrigerant during commissioning. In the US, HVAC technicians handling refrigerant need EPA Section 608 certification, and many states additionally require a state HVAC contractor licence. These aren't optional extras. They're the baseline that should already be true of anyone quoting the job.

Manufacturer authorisation and warranty

Check whether the installer is an authorised dealer for the brand they're quoting, particularly if the manufacturer's extended warranty terms require authorised installation to remain valid. This varies by brand and is worth confirming directly rather than assuming, since I've seen warranty claims complicated by this exact gap. It's a quick email to the manufacturer if the installer can't answer clearly on the spot.

The sizing method is the real test

A proper heat-loss and heat-gain calculation accounts for your home's actual insulation levels, window area and orientation, ceiling height, air leakage, and local climate data, not just floor area. I've written elsewhere about why oversizing is a common and costly mistake: an oversized unit short-cycles, which is harder on the compressor and, in cooling mode, worse for humidity control than a correctly sized unit running longer, steadier cycles. Ask directly whether the quote is based on an actual calculation or a rule-of-thumb estimate, and ask to see the numbers, not just the recommended unit size.

What a proper quote should itemise

Beyond the equipment itself, a trustworthy quote should specify the exact model and capacity being installed, not just "a heat pump," whether the install is ducted or split and what that includes, any electrical work required, commissioning and testing procedures, and warranty terms for both the equipment and the installation labour separately. These are sometimes different lengths and it's worth knowing which is which.

Questions about ongoing service and parts

Ask what a routine service actually involves, filter cleaning, refrigerant pressure checks, coil inspection, and how often it's recommended for your climate and usage. Also ask about parts availability for the specific brand and model, particularly for a less common brand, since a compressor fault years down the track is a very different experience if parts are readily stocked locally versus a multi-week import wait. I've had clients caught out by this exact gap on an otherwise good unit from a smaller brand.

Red flags

A quote with no mention of a heat-loss calculation, one recommending a noticeably larger unit than a genuine calculation would suggest "for flexibility," or an installer who can't explain the COP or capacity curve of the specific unit they're recommending at your local design temperature, all worth pausing on. So is a rushed sales process that discourages you from getting a second quote, which is a pattern that shows up across trades generally, not just heat pumps.

My honest take

I'd trust an installer who spends real time asking about your home's insulation, window coverage and how you actually use each room over one who quotes off a floor plan alone. The sizing conversation is where the real expertise shows up. The equipment brand matters less than most marketing suggests once you're comparing reputable manufacturers.

See our pieces on ducted vs split-system heat pumps and cold-climate heat pump ratings for the equipment-selection side of this decision, and our heat pumps hub for the rest of the sizing and running-cost content.

In Australia, refrigerant handling licensing sits under the Australian Refrigeration Council, and in the US, EPA Section 608 certification governs refrigerant handling, both worth checking directly rather than taking an installer's word for it.

What I'd ask about commissioning specifically

A properly commissioned heat pump should have refrigerant charge verified against manufacturer specification, airflow checked across the indoor unit or ducted system, and controls configured and explained to you before the installer leaves. Ask whether commissioning documentation, actual measured readings, not just a tick-box form, will be provided. A rushed commissioning process is one of the more common reasons a technically correct installation still underperforms its rated efficiency in practice, and it's genuinely hard for a homeowner to catch after the fact without documentation to compare against.

References and past work

Ask for references from jobs of a similar scale and system type to yours, not just a general testimonial list, and if possible ask to see a completed ducted install if that's what you're getting, since ducted and split installs involve quite different skill sets and it's reasonable to want evidence of both if you're comparing installers who claim to do both well.

What a rushed quote conversation tells you

I'd treat a quote appointment that's over in fifteen minutes with real suspicion for anything beyond a straightforward single split replacement. A genuine sizing conversation, walking the home, discussing insulation and window coverage, checking the existing electrical supply, takes real time, and an installer unwilling to spend that time at the quote stage is unlikely to spend it at commissioning either.

Getting a second opinion on a sizing recommendation

If a recommended unit size seems large relative to what you expected, it's entirely reasonable to get a second installer's independent calculation rather than just accepting the first one. I'd never take offence at a client doing this, and any installer who does is telling you something about how confident they actually are in their own numbers.

What good aftercare looks like

Ask what happens if something feels wrong in the first few weeks after commissioning, is there a settling-in check included, and how quickly a genuine fault gets responded to under warranty. A good installer treats commissioning as the start of the relationship, not the end of the transaction, and their answer to this question tells you a fair bit about which kind of business you're dealing with.

How long a genuinely good business has been trading

I'd weigh a business's track record specifically in heat pump installation, not just general HVAC or electrical work generally, since the sizing and refrigerant-handling skill this trade needs is genuinely specific. A newer business isn't automatically worse, but it's worth asking directly about the individual technician's own experience with heat pumps specifically, rather than assuming the company's overall years in business tells you everything about the person actually doing your install.

— Priya Nathan, Heat pumps & HVAC

Tagged

Common questions

Should I always go with the cheapest quote?
No. I'd weigh a quote that includes a proper heat-loss calculation and correctly matched equipment more heavily than a lower price with vaguer scope. An oversized or undersized system costs you in running costs and comfort for the life of the equipment, which usually dwarfs the install-price difference.
Does manufacturer authorisation matter that much?
It matters more for warranty validity than for raw competence. Some manufacturer warranties require installation by an authorised dealer to remain valid, so check this specifically if warranty length was part of why you chose that brand.
About the author
PN
Priya Nathan
Heat pumps & HVAC · Melbourne, AU

Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.

Mechanical engineering background; ex-HVAC design.

More from Priya Nathan