Vetting a double glazing repair or reglazing tradesman: what to check
I got a call two weeks ago from a reader in Ocean Grove whose ten-year-old double-glazed unit had gone cloudy at the bottom corner. Not the whole window, just one insulated glass unit (IGU) in a bank of six. She'd had three quotes: one for $180 to reglaze that single unit, one for $2,400 to replace the entire window, and one guy who didn't quote at all, just said "yeah I can sort that mate" and asked for cash up front. Guess which one she called me about.
This is a narrower job than a full window and glazing install, and it gets treated far too casually by homeowners because the failure looks small. A fogged IGU is a sealed-unit failure, moisture's got past the desiccant and the argon or air gap, and the fix is either a full sash/frame replacement or a reglaze where the glazier cuts the old sealed unit out and fits a new one into the existing frame. That second option is cheaper and often the right call, but it's also where a lot of dodgy work happens, because it looks like "just swapping some glass" to someone without the right ticket.
Why this is a different licensing question to a full glazing install
My colleague's already covered vetting a window and glazing installer for full replacements, and a lot of that overlaps here: glazing licence, manufacturer accreditation, AS 1288 compliance for the glass itself. But reglazing an existing frame has its own failure points that a full-window job doesn't, because the tradesman is working with what's already there rather than starting fresh.
The frame's existing rebate (the recess the glass sits in) has to be measured accurately, and if the original installer cut corners on drainage or the frame's swollen slightly over ten years, a reglaze can trap moisture again within a couple of years. A full window replacement sidesteps that because the whole assembly is new. A reglaze inherits whatever's already wrong with the frame. That's the first thing I ask anyone quoting this job: are they inspecting the frame condition, or just measuring for a replacement pane and moving on.
The licence that actually applies
In most Australian states, glazing work sits under a specific glazing licence or is captured within a broader building licence depending on jurisdiction, this varies state to state so check your local regulator rather than assume. Victoria's Victorian Building Authority (VBA) and NSW's Fair Trading both maintain public licence search tools, and I'd treat "I've been doing this for years" as no substitute for actually looking the licence number up. Ask for it before the quote, not after you've paid a deposit.
What trips people up is that reglazing specifically, as opposed to new window installs, sometimes gets treated by unlicensed operators as a "handyman" job because it doesn't involve structural work or waterproofing to the same degree. That's a grey area some tradies exploit. If someone quotes a reglaze and can't produce a licence number, or gets vague when you ask which state body they're registered with, that's your first red flag and it should end the conversation.
Manufacturer accreditation matters more than you'd think
Double glazing units aren't generic. The spacer bar, the desiccant, the seal type (usually a dual-seal system, an outer structural seal over an inner vapour barrier) all come from a specific manufacturer's specification, and warranties on IGUs are typically tied to installation being done to that manufacturer's method. If your original glazing was installed under a brand-specific accreditation program, a reglaze done outside that program can void the remaining warranty on the surrounding units even if the new IGU itself is fine.
I always ask two questions here: who manufactures the replacement IGU, and is the installer accredited with that manufacturer specifically, not just "an installer" in general. A properly accredited reglazer will tell you the U-value and SHGC (solar heat gain coefficient) of the replacement unit without having to check a folder. If they can't answer that on the spot, they're not working closely enough with a manufacturer to be trusted with a warranty-sensitive repair.
Red flags that show up specifically in reglazing quotes
A few things I've learned to watch for, some from readers, some from watching quotes come in on my own place over the years.
No mention of drainage weep holes in the quote. If the frame's weep holes (the small drainage points at the base of the frame that let condensation escape) are blocked or were never cut properly on the original install, a reglaze without addressing them just recreates the fogging problem in a few years. A tradesman who's actually checking the frame will mention this unprompted.
Vague argon or krypton gas fill claims. If the original unit was gas-filled for thermal performance and the quote doesn't specify whether the replacement will be gas-filled too, ask directly. Cheaper reglazes sometimes quietly downgrade to an air-filled unit, which changes your U-value and, frankly, your whole reason for having double glazing in the first place.
Cash-only, no invoice, no warranty paperwork. This one's not glazing-specific, it applies to every trade on this list, but I still hear about it constantly. A reglaze with no written warranty on the seal is a reglaze you should assume will fail again within five years.
No measurement of the actual rebate depth. If someone quotes over the phone from a photo without visiting, or measures the visible glass without checking the rebate depth and drainage, they're quoting a generic job onto a specific frame. That's how you end up with a unit that doesn't seat properly and fails early.
What a legitimate reglaze quote should actually include
A proper quote for this work should specify the glass makeup (thickness of each pane, spacer width, gas fill if applicable), confirm which manufacturer's IGU is being used, state the seal type, and include a written warranty period, usually somewhere in the 5-10 year range for seal failure depending on the manufacturer, though I'd always confirm the exact term rather than assume. It should also note whether the frame's being inspected for drainage and rebate condition before the new unit goes in, not just measured for size.
Honestly, I think a lot of homeowners under-quote this job in their own head before they even ring anyone. They assume "it's just glass" and go looking for the cheapest option, when the actual risk here is a seal failure recurring in three years because nobody checked the frame properly the first time. I'd rather pay a bit more for someone who inspects the frame and tells me the weep holes are half-blocked than take the $180 quote from the tradesman who never got out of his ute.
When a reglaze isn't actually the right fix
Sometimes the honest answer from a good glazier is that reglazing isn't worth it. If the frame itself has warped, if there's visible timber rot around a timber-framed unit, or if the fogging is happening across multiple units in the same bank within a short window of each other, that's usually a sign the whole assembly is reaching end of life rather than one unit having failed in isolation. A tradesman who pushes hard for a reglaze in that situation, rather than raising a full replacement, is either not looking closely enough or is quoting the cheaper job because it's an easier sale.
This is also where your NatHERS or HERS rating paperwork, if you've had one done, can actually help. It'll usually list the glazing spec for each opening, which gives you a baseline to check the replacement unit against, and it's a useful cross-check against a tradesman who might otherwise talk you into whatever stock he's got on the truck. And if you're weighing up whether the extra cost of upgrading to a higher-performance unit while you're already reglazing is worth it, our piece on double vs triple glazing is worth a read before you sign anything.
The Australian Glass and Glazing Association publishes technical guidance for members on IGU installation and seal performance that's a useful reference point if you want to check what a reglaze should look like before the tradesman arrives, and the Australian Building Codes Board's National Construction Code sets the performance requirements that glazing has to meet in the first place, including relevant AS 1288 glazing standards. Worth a skim if you're the type who reads the fine print, which, if you're vetting a trade this closely, you probably are.
Common questions
- Is reglazing a single IGU cheaper than replacing the whole window?
- Usually yes, a reglaze that swaps just the failed insulated glass unit into the existing frame is typically a fraction of the cost of a full window replacement, but only if the frame itself is in good condition. If the frame's warped, rotted, or has ongoing drainage issues, a reglaze can end up being a shorter-term fix than it looks.
- Does a reglaze need the same licence as a full window installation?
- In most Australian states, glazing work of any kind sits under a glazing licence or a relevant building licence, though the exact framework varies by state. Check your state regulator's public licence search before booking, some operators treat reglazing as informal handyman work when it isn't.
- How do I know if the fogging will come back after a reglaze?
- Ask whether the tradesman checked and cleared the frame's weep holes and confirmed the rebate is dry and undamaged before fitting the new unit. Fogging often returns when the underlying drainage problem that caused the original seal failure was never addressed.
- Should the replacement IGU match the original gas fill and spacer type?
- Ideally yes, if the original unit was argon-filled for thermal performance, a downgrade to an air-filled replacement will measurably change your U-value. A properly accredited installer should be able to quote the replacement unit's specification without hesitation.
Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.
Building-certification background (NatHERS-adjacent).
More from Ben Sorensen
- Why a NatHERS or HERS rating can change without touching the buildA NatHERS or HERS rating can shift star bands when software updates, climate files get revised, or rules change — even if your house hasn't.
- Why your NatHERS or HERS rating ignores your floor coveringsCarpet, tile and polished concrete all score the same in a NatHERS or HERS model, even though they feel wildly different underfoot and change how your heating actually performs.
- Vetting an insulation installer: the R-value receipt nobody asks forInsulation installers rarely need a specific trade licence, which is exactly why the paperwork trail matters more than the handshake.
- Why your NatHERS or HERS rating never touches your thermal bridgesA NatHERS or HERS rating models your walls as flat layers, which means steel studs, balcony slabs and window reveals rarely get the credit (or blame) they deserve.
- Why your NatHERS or HERS rating never checks your orientation on siteYour NatHERS or HERS star rating locks in orientation at design stage, but nobody re-checks it once the slab is poured the wrong way round.
- Vetting a window glazier for new-build glazing: what to checkBefore a glazier touches your new-build windows, check the licence, the AS 2047 compliance paperwork and the install method. Here's what actually matters.