Vetting a window glazier for new-build glazing: what to check

By Ben Sorensen · November 3, 2026 · 8 min read
Writing notes on a quote or contract at a desk
Photo by Scott Graham on Unsplash

Three weeks ago I stood in a half-framed house on Erindale Street in Ballarat with a builder who'd already had one glazier walk off the job after a dispute over flashing details. The windows were still shrink-wrapped on pallets in the garage. The client wanted to know one thing: how do you pick a glazier for a new build without ending up back here in eighteen months with condensation streaming down the inside of the glass?

It's a fair question, and it's different from vetting a repair or reglazing trade. New-build glazing is structural and thermal work bundled into one job. The glazier isn't just fitting glass into a frame someone else built; in a lot of cases they're also responsible for the window unit itself, the flashing interface with the wall wrap, and the compliance paperwork that a building surveyor will eventually want to see. Get this wrong and you're not dealing with a squeaky hinge. You're dealing with water ingress behind cladding, or a NatHERS-certified home that performs nothing like its rating because the installed glazing doesn't match what was modelled.

Why new-build glazing is a different beast to a repair job

When a homeowner replaces a cracked pane, the stakes are contained. If the seal fails, you get a fogged unit and you replace it. New-build glazing sits inside the building envelope in a much more structural way. Window and door openings are load-bearing junctions. They interrupt the wall wrap, the flashing tape, the sarking. A poorly installed unit doesn't just leak air, it can let bulk water track down inside a wall cavity for years before anyone notices the stain on the skirting board.

I've written before about how a NatHERS or HERS rating never actually checks your windows' installation quality, and this is the practical end of that problem. The energy rating assessor models a U-value and a SHGC off the glazing spec sheet. Nobody from the rating scheme turns up on installation day to check whether the glazier actually used the specified spacer, sealed the frame-to-wall junction correctly, or installed the unit plumb and square. That's entirely on the trade you hire, and on whoever is meant to be inspecting their work.

The licence check that actually matters

In most Australian states, glazing work above a certain threshold needs a licensed glazier or a licensed builder overseeing the installation, and the specific licence class varies by jurisdiction. Victoria runs it through the Victorian Building Authority, NSW through Fair Trading, Queensland through the QBCC. Don't just ask "are you licensed" and accept a verbal yes. Ask for the licence number and look it up yourself on the relevant public register. It takes two minutes and it tells you whether the licence is current, what class of work it covers, and whether there are any disciplinary notes against it.

What the register won't tell you is whether the glazier has actually handled a high-performance glazing package before. I'd treat that as a bigger red flag than a borderline licence question, honestly. A trade who's spent fifteen years fitting single-glazed aluminium sliders into older homes may hold a perfectly valid licence and still have no real feel for the clearances, packer placement and sealant compatibility that double or triple glazed units with thermally broken frames demand. Ask directly: how many double-glazed, thermally broken frame installs have you done in the last twelve months? A vague answer is worth more than the licence card.

AS 2047 and the compliance paperwork nobody asks for

Windows and doors in Australian residential construction are generally expected to comply with AS 2047, the standard covering windows in buildings, which sets requirements for structural performance, water resistance and weatherproofing testing. A legitimate glazing supplier should be able to produce a Window Energy Rating Scheme (WERS) label or equivalent test data, and ideally a statement of compliance tying the specific window model to the wind rating required for your site.

Here's the gap I keep finding: the compliance documentation for the window unit itself is usually fine, because the manufacturer did the testing. What's almost never documented is the installation. There's no standard certificate that says "this unit was installed per AS 2047 clearances and per the manufacturer's fixing instructions." That paperwork hole is exactly where disputes happen later, so I tell clients to ask the glazier in writing, before the job starts, whether they'll supply photos of the flashing and sealant work before the cladding goes over it. Any glazier who balks at that request is telling you something.

Red flags that show up before the quote even lands

A few patterns repeat often enough that I now treat them as near-automatic disqualifiers. A glazier who quotes window supply and installation as a single lump sum with no line-item breakdown of frame specification, glass spec (including spacer type and gas fill if it's double glazed), and installation method is usually hiding margin somewhere in that bundle. Ask for the breakdown. If they resist, that's the red flag, not the request.

Another one: a glazier who can't tell you which sealant they're using at the frame-to-reveal junction, or whose answer is "whatever's cheapest at the merchant that week." Sealant compatibility with the frame material and the wall wrap matters more than most homeowners realise, and a trade who treats it as an afterthought probably treats the flashing detail the same way.

I'd also flag anyone quoting a job on a new build without asking to see the architectural drawings or at minimum the window schedule. A glazier who's happy to quote blind off a phone call hasn't thought about reveal depth, drainage paths, or how the unit interacts with the specific cladding system on your job. That's a genuinely bad sign on a new build, less so on a straightforward like-for-like reglaze.

Where the building surveyor fits in, and where they don't

Clients often assume the private building surveyor or council inspector will catch glazing defects during a mandatory inspection stage. In my experience that's optimistic. Frame and window inspections, where they happen at all, are usually a visual check that the openings match the approved drawings, not a detailed audit of flashing tape overlap or sealant bead continuity. The surveyor is checking compliance with the permit, not performing quality assurance on workmanship.

This is one of those spots where I'll push back a little on how the industry presents these inspection stages. Builders and clients alike tend to treat a passed inspection as a signal that everything behind the wall is sound. It mostly isn't a signal of that at all; it's a signal that the opening size and location match the plans. If you want actual assurance on install quality, you arrange it yourself, either through photos at each stage or by engaging a separate building inspector who understands building science, not just permit compliance.

What good glazing handover paperwork looks like

At minimum I want to see, for every new-build glazing job: the WERS or manufacturer compliance certificate for each window and door unit, matched against the window schedule by location and reference number; photographic evidence of the flashing and sealant detail at each opening, taken before cladding or lining covers it; and a written warranty that separately states what's covered on the unit (usually the manufacturer) versus the installation (the glazier). Those are three different documents and three different responsible parties, and conflating them is how warranty claims get stuck in limbo later.

If your project also involves a NatHERS or HERS energy assessment, it's worth cross-checking the actual installed glazing spec against what was modelled in the rating. I've seen enough cases where a builder value-engineered a glazing substitution mid-build, changed the spacer type or dropped from double to single glazing on a minor elevation, without updating the as-built energy model. The rating is a design tool, not a build receipt, and nobody chases that gap for you automatically.

A practical sequence before you sign

Pull the licence number and check the state register yourself. Ask for a line-item quote separating frame, glass spec and installation. Ask specifically about sealant choice and recent double-glazed install experience. Request flashing photos as a contract condition, not a favour. And match the final compliance certificates against your window schedule before the final payment goes out, not after.

None of this is exotic. It's the same discipline I'd apply vetting a sealant and flashing trade or checking a double glazing repair tradesman on an existing home, just applied earlier in the build when the stakes of getting the envelope wrong are higher because everything else, the insulation, the HVAC sizing, the energy rating, gets built around whatever the glazing actually delivers. For broader guidance on the standard your windows should meet, the Australian Building Codes Board publishes the relevant performance requirements under the National Construction Code, and the Window Energy Rating Scheme operated through the Australian Window Association is worth checking directly against your supplied unit's rated performance.

That client on Erindale Street ended up re-quoting with two glaziers before picking one who sent flashing photos unprompted on the first job he showed us as a reference. Small thing. Told us plenty.

— Ben Sorensen, Green Building, IceWarm

Tagged

Common questions

Does a glazier need a separate licence from a builder to install new-build windows?
In most states, yes for work above a certain scope, though the exact threshold and licence class varies by jurisdiction. Check the specific licence number against your state's public building licence register rather than taking a verbal assurance.
What is AS 2047 and why does it matter for new-build glazing?
AS 2047 is the Australian Standard covering windows in buildings, setting structural, water resistance and weatherproofing performance requirements. It covers the window unit's tested performance, but not installation quality, which is a separate thing to verify.
Should I ask for photos of flashing before cladding covers the windows?
Yes. Flashing and sealant detail at the frame-to-wall junction becomes invisible once cladding or internal lining goes up, and it's one of the most common sources of later water ingress disputes. Make photographic evidence a contract condition.
Can a building surveyor catch poor glazing installation during inspections?
Usually not in detail. Standard inspection stages typically confirm opening size and location match approved drawings, not workmanship quality like sealant continuity or flashing overlap. Arrange separate documentation if you want that assurance.
About the author
BS
Ben Sorensen
Green building · Perth, AU

Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.

Building-certification background (NatHERS-adjacent).

More from Ben Sorensen