Vetting a draught-proofing or weatherisation trade: licences and red flags

By Ben Sorensen · September 16, 2026 · 7 min read
Electrician at work on a residential site
Photo by Emmanuel Ikwuegbu on Unsplash

A bloke turned up to a rental I was inspecting on Crampton Street in Geelong last month with a caulking gun, a roll of foam tape, and absolutely nothing else. No blower door, no thermal camera, no paperwork. He called himself a "weatherisation specialist." When I asked what standard he worked to, he shrugged and said "just common sense, mate." That's the whole problem with this trade in one driveway conversation.

Draught-proofing and weatherisation sit in an odd regulatory gap. Unlike electrical or plumbing work, there's no dedicated trade licence in most Australian states or US jurisdictions for sealing gaps around windows, skirting boards, exhaust fans and cornices. Anyone can buy expandable foam and a caulking gun and call themselves a specialist. That doesn't mean the work is unregulated, though — it means the checks fall on you, the homeowner, and most people don't know what to ask.

Why there's no single licence for this trade

Draught sealing is a subset of general building or handyman work in Australia, which means the legal threshold is usually just a state building licence or, in some jurisdictions, no licence at all for jobs under a certain dollar value. In the US it's similarly patchy — weatherisation contractors sometimes need a state home-improvement licence, sometimes nothing beyond a business registration, unless they're working under a government-funded programme.

Where it gets more serious is when draught-proofing touches other regulated systems. Sealing around a gas flue, a exhaust fan penetrating a fire-rated ceiling, or a wet area vent isn't just caulking — it can affect combustion safety or fire compliance under the relevant building code. That's where I get genuinely fussy about who's doing the work, because a badly sealed flue gap is a different order of problem to a draughty window.

The certification that actually matters

In the US, the closest thing to a real trade credential here is Building Performance Institute (BPI) certification, specifically BPI's Building Envelope or Air Leakage Control credentials, which require a practical exam and knowledge of building science, not just product application. A contractor who holds a BPI certification has demonstrated they understand pressure boundaries, moisture movement and combustion safety, not just how to run a bead of sealant.

Australia doesn't have an equivalent single national credential, but the Clean Energy Council and various state-based building practitioner registers are the closest proxies, and a NatHERS-accredited assessor working alongside the installer is a genuinely good sign — it means someone competent is measuring the before-and-after, not just eyeballing it. I've written before about vetting a blower door and thermal imaging auditor, and the overlap here is real: a lot of the best draught-proofing outfits are auditors who also do the sealing work, or who subcontract it to someone they trust and then re-test.

Red flags I look for on the first visit

The first tell is whether they measure anything before quoting. A legitimate weatherisation contractor either brings a blower door themselves or asks whether one has already been run on the house. If the answer to "how do you know where the leaks are" is "I can just feel the draught," that's someone quoting off vibes, not data.

Second tell: material choice without explanation. Expandable polyurethane foam is fine for some gaps but wrong for others — it's not fire-rated, it shouldn't go anywhere near a flue clearance, and it degrades under UV. A contractor who reaches for the same foam can for every gap in the house, including around a gas appliance penetration, hasn't thought about where sealing helps and where it creates a different problem.

Third: no mention of make-up air. Seal a house too aggressively without addressing ventilation and you can end up with elevated indoor humidity, condensation on cold surfaces, or in the worst case, back-drafting of combustion appliances. I'd rather work with someone who talks about balanced ventilation, even briefly, than someone who treats "tighter is always better" as gospel. It genuinely isn't — past a certain point without mechanical ventilation, you're trading a draught problem for a moisture problem.

Fourth: no post-work test. If a contractor won't quote a before-and-after blower door number, or at minimum a visual thermal scan comparison, you have no way of knowing whether the several hundred dollars you spent achieved anything measurable. Reputable outfits will happily show you the air-changes-per-hour figure before and after.

What paperwork should exist

For anything touching a gas appliance flue, exhaust duct penetration, or fire-rated ceiling or wall, ask for written confirmation that the relevant clearances under the local building code and, where gas is involved, the applicable gas installation standard, haven't been compromised. In Australia that's typically referenced against AS/NZS 5601 for gas installations; a draught-proofer sealing around a flue penetration without understanding this standard is a liability, not a tradesperson.

You should also get an itemised scope: which gaps were sealed, with what material, and why. "General draught sealing, $650" on an invoice tells you nothing. A proper scope might read: skirting board gaps on the southern wall, exhaust fan surround in the main bathroom, gap around the evaporative cooling duct in the hallway ceiling. That level of detail lets you sanity-check the work later, and it's the same principle I've argued for elsewhere around solar and battery quotes — a vague line item usually means vague thinking behind it.

Where this connects to the rest of your envelope

Draught sealing is cheap relative to insulation or glazing upgrades, but it's not a substitute for them, and the order of operations matters more than most homeowners realise. I've made the case before that air sealing should happen before insulation, not after, because sealed gaps stop insulation from being short-circuited by air movement through it. If your contractor is sealing gaps in a roof space that's about to get a fresh batt or blown-in insulation job, coordinate the sequence, and check that whoever does the insulation work meets the standards I've outlined in vetting an insulation installer's licence.

It's also worth checking whether draught sources are actually glazing-related before you pay someone to chase skirting boards. A tired aluminium-framed window with failed seals can leak more air than every gap in your architraves combined, and no amount of caulking fixes that. If you suspect the window itself, that's a different trade and a different set of checks, covered in vetting a window and glazing installer.

Questions worth asking before you sign anything

I keep this list short deliberately, because a contractor who can't answer these plainly usually isn't worth hiring regardless of price. Ask whether they'll run or reference a blower door test before and after. Ask what they do differently around gas flues, exhaust fans and fire-rated assemblies versus a plain skirting board gap. Ask how they think about make-up air once the house is sealed tighter. Ask for a written, itemised scope rather than a lump sum.

None of these questions require you to understand building science yourself. They just require the tradesperson to demonstrate they do. The guy on Crampton Street couldn't answer any of them, and the homeowner, to her credit, sent him packing before he touched the caulking gun.

I'll admit I used to think draught sealing was low-stakes enough not to bother with heavy vetting — mostly true for a gap under a door, less true once gas appliances and roof cavities are involved. The U.S. Department of Energy's weatherisation guidance and the Clean Energy Council's installer resources are both useful starting points if you want the underlying building-science reasoning rather than just my take on it.

For the bigger picture on what order to tackle envelope work in, and where draught sealing sits relative to insulation, glazing and heating system upgrades, our green building hub and trades vetting hub both have more on sequencing and contractor checks.

Tagged

Common questions

Is there a specific licence required for draught-proofing work?
Not usually a dedicated one. In most Australian states it falls under general building or handyman licensing thresholds, and in the US it's often unregulated below a certain job value unless the contractor works under a government weatherisation programme. The BPI Building Envelope credential is the closest thing to a real trade-specific qualification in the US market.
Can sealing draughts around a gas flue be dangerous?
Yes, if done without understanding combustion air and clearance requirements. Sealing too close to a flue or exhaust penetration can affect appliance venting and should be checked against the relevant gas installation standard, AS/NZS 5601 in Australia, rather than treated as routine caulking.
Should I seal my house as tightly as possible?
No. Past a certain point, sealing without addressing ventilation increases indoor humidity and condensation risk. A competent contractor will talk about make-up air or balanced ventilation, not just chase every gap they can find.
Does draught sealing replace the need for insulation upgrades?
No, they solve different problems. Draught sealing stops air movement through gaps; insulation slows heat transfer through materials. Air sealing generally makes more sense to do first, since it stops insulation being undermined by air leakage.
About the author
BS
Ben Sorensen
Green building · Perth, AU

Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.

Building-certification background (NatHERS-adjacent).

More from Ben Sorensen