Air sealing and blower door contractors: licensing and red flags to check
I was on a job in Bell Post Hill a few months back, standing in a roof void with a homeowner who'd just paid a contractor to "air seal the whole house" for a fee that, frankly, wouldn't have covered materials for the attic penetrations alone. No blower door test before, none after. No photos. A single tube of caulk sitting in the corner told the real story. She had no way of knowing whether the job did anything at all, because there was nothing to measure it against.
That's the core problem with air sealing as a trade: almost anyone can call themselves an air sealing contractor. Unlike electrical or plumbing work, there's often no dedicated licence you must hold to caulk a rim joist or foam a penetration. That gap is exactly where the industry's worst operators live, and it's why the checks you do before signing matter more here than for almost any other home-energy trade.
Why air sealing has a licensing blind spot
In most Australian states, general building or handyman licensing thresholds are based on the dollar value of work, not the trade category itself. A contractor doing $3,000 of caulking and weatherstripping can often sit under the threshold that would require a builder's licence, and air sealing isn't gas, isn't electrical, isn't plumbing, so none of those trade licences apply either. In the US it's similar: air sealing sits inside general contracting or weatherisation categories that vary wildly by state, and some states have no specific credential requirement at all.
What does exist, and what you should actually be asking for, is Building Performance Institute (BPI) certification in the US, specifically BPI Building Analyst or BPI Envelope Professional, and in Australia the closest equivalent is a contractor who can demonstrate blower door competency, ideally tied to a NatHERS assessor relationship or a Home Energy Efficiency scheme. Neither is a legal requirement to pick up a caulking gun. Both are the clearest signal you're dealing with someone who understands building science rather than someone who just knows how to spray foam into a gap.
The blower door test is non-negotiable
I've written before about why air sealing has to happen before insulation goes in, and the same logic applies to proving the work happened at all. A blower door test depressurises the house and measures air changes per hour, giving you a number before work starts and a number after. Without that before-and-after pair, you are trusting the contractor's word that anything changed. Any contractor doing air sealing properly owns a blower door or subcontracts one in in for testing. If they don't test, or say testing is "not really necessary for this kind of job," that's the first red flag and it's a hard stop for me. The ENERGY STAR guidance on sealing and insulating is explicit that a blower door test should bookend any serious air sealing project, and it's one of the few free, publicly available references homeowners can point to when a contractor pushes back.
What a proper test result looks like: a report showing air changes per hour at 50 pascals (ACH50) before and after, with the target improvement stated as a percentage, not a vague "it'll feel tighter." Ask for that report before you pay the final invoice, not just before you sign.
Combustion safety is where sloppy sealing turns dangerous
This is the part that genuinely worries me, and it's not theoretical. Tighten a house without checking what's drawing combustion air, and you can turn a gas water heater or an open-flued gas heater into a carbon monoxide risk. Depressurisation from exhaust fans, range hoods, and clothes dryers can backdraft a flue that used to vent fine in a leakier house. A contractor who understands building science tests for this. In the US that's a **combustion appliance zone (CAZ) test**, part of the BPI protocol, checking spillage and draft on gas appliances after sealing is complete. In Australia, the equivalent diligence is checking flue draft on any open-flued gas appliance and, ideally, recommending its replacement with a sealed or electric unit if it can't be verified safe. If a contractor doesn't mention combustion safety at all when scoping a whole-house air seal, ask directly. If they look blank, that's your answer.
I'd rather see a homeowner spend an extra afternoon organising a proper CAZ-style check than save a few hundred dollars and end up with a flue backdrafting into a bedroom hallway. That's not a hypothetical scare line, it's the actual mechanism, and it's well documented in the building science literature that underpins the BPI standard.
Reading a real quote versus a padded one
A legitimate air sealing quote itemises location, not just a lump sum. Rim joists, top plate penetrations, recessed downlights, the gap around the manhole cover, service penetrations for plumbing and electrical, weatherstripping on doors — each should appear as its own line, ideally with the sealing method named (fire-rated sealant near downlights, expanding foam for larger gaps, mastic or foil tape for duct connections). We've covered this pattern before for solar and battery quotes in what a real solar or battery quote should itemise, and it holds just as true here: a one-line "whole house air seal — $X" quote is hiding either scope or corner-cutting, and usually both.
Watch for quotes that promise a specific percentage improvement in tightness before they've even done a pre-test. You cannot honestly promise a 30% reduction in air changes without first knowing the baseline. That's marketing, not measurement.
Questions worth asking before you sign anything
I keep a short list I run through with clients, and it doubles as a decent filter on the phone before a quote visit even happens.
Ask whether they'll run a blower door test before and after, and whether that report is included in the price or costs extra. Ask what happens if the house has an open-flued gas appliance, specifically what combustion safety check they'll do post-sealing. Ask for two recent addresses where they've done comparable work, not just a testimonial page, an actual street they worked on that you could drive past if you wanted to. Ask how they handle roof space ventilation once the house is tighter, because sealing without addressing bulk ventilation in a roof cavity can shift moisture problems rather than solve them. And ask, plainly, what standard or certification they hold, then actually check it rather than taking the answer at face value.
None of this is exotic. It's the same due diligence that applies to vetting a heat pump installer or questioning an insulation contractor, just pointed at a trade with a thinner regulatory net underneath it.
What a good result actually looks like on paper
When the work is done properly, you end up with a document trail: a pre-seal blower door number, a scope of work matched against room-by-room photos, a post-seal blower door number showing a meaningful drop in ACH50, and a combustion safety note if the home has gas appliances. If your NatHERS assessment or HERS rating is part of a broader renovation, that paperwork should also feed into what a NatHERS or HERS assessor checks on-site, because air tightness is one of the inputs to the star rating, and sealing work done without documentation is invisible to a future assessor too.
Honestly, I think the industry would be better served by a proper trade licence category for air sealing specifically, the way electrical and plumbing already have one. Until that exists, the paperwork is the licence. Ask for it, read it, and don't pay the final invoice until the after-test number is in your hand.
— Ben Sorensen, Green Building Writer
Common questions
- Is there a specific licence required to do air sealing work?
- In most Australian states and many US states, no dedicated trade licence exists for air sealing specifically. It often falls under general handyman or building licensing thresholds based on job value. The closest thing to a real qualification is BPI certification in the US or demonstrated blower door competency tied to energy rating work in Australia.
- What is a blower door test and why does it matter here?
- A blower door test uses a calibrated fan to depressurise the house and measure air changes per hour. It's the only objective way to prove air sealing work actually reduced leakage, rather than taking a contractor's word for it. Ask for before-and-after ACH50 numbers in writing.
- Can air sealing a house create a safety problem?
- Yes, if the home has open-flued gas appliances. Tightening a house changes pressure dynamics and can cause a flue to backdraft, pushing combustion gases back into the living space. A qualified contractor checks combustion safety after sealing, particularly around gas water heaters and gas heating appliances.
- Should air sealing happen before or after insulation is installed?
- Air sealing should always happen first. Insulation slows heat transfer but does nothing to stop air leakage, and sealing gaps after insulation is installed is far harder and often incomplete. See our piece on the correct order of operations for more detail.
- What should be in a proper air sealing quote?
- A real quote itemises each location being sealed (rim joists, penetrations, downlights, manhole covers, ductwork) with the method noted for each, plus inclusion of pre- and post-work blower door testing. A single lump-sum line for 'whole house air seal' with no detail is a red flag.
Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.
Building-certification background (NatHERS-adjacent).
More from Ben Sorensen
- Why a NatHERS or HERS rating can change without touching the buildA NatHERS or HERS rating can shift star bands when software updates, climate files get revised, or rules change — even if your house hasn't.
- Why your NatHERS or HERS rating ignores your floor coveringsCarpet, tile and polished concrete all score the same in a NatHERS or HERS model, even though they feel wildly different underfoot and change how your heating actually performs.
- Vetting an insulation installer: the R-value receipt nobody asks forInsulation installers rarely need a specific trade licence, which is exactly why the paperwork trail matters more than the handshake.
- Why your NatHERS or HERS rating never touches your thermal bridgesA NatHERS or HERS rating models your walls as flat layers, which means steel studs, balcony slabs and window reveals rarely get the credit (or blame) they deserve.
- Why your NatHERS or HERS rating never checks your orientation on siteYour NatHERS or HERS star rating locks in orientation at design stage, but nobody re-checks it once the slab is poured the wrong way round.
- Vetting a window glazier for new-build glazing: what to checkBefore a glazier touches your new-build windows, check the licence, the AS 2047 compliance paperwork and the install method. Here's what actually matters.