Why your heat pump sounds louder in winter (it's not a fault)

By Priya Nathan · August 18, 2026 · 7 min read
White heat pump / air conditioner outdoor unit mounted on a brick wall
Photo by Everett Pachmann on Unsplash

I got a call last July from a client in the Dandenong Ranges convinced her two-year-old heat pump was "dying." Her exact words: "it sounds like someone's shaking a tin shed out there." I drove up, stood next to the outdoor unit for ten minutes in the cold, and told her the system was doing exactly what it was designed to do. She didn't love that answer, but it was true.

This is one of the most common service calls I hear about between June and August, and it's almost never a fault. It's a defrost cycle, and understanding what's actually happening mechanically will save you a call-out fee and a lot of worry.

What's actually making the noise

A heat pump's outdoor coil gets cold, colder than the surrounding air, because that's the whole point: it's extracting heat from air that might only be a few degrees above zero. When the coil temperature drops below the dew point of the air passing over it, moisture condenses on the fins. Below about 5°C ambient, that moisture doesn't just condense, it freezes.

Left alone, that frost layer would build up and block airflow through the coil entirely, killing performance. So the system periodically reverses the refrigeration cycle for a few minutes, essentially running as an air conditioner in reverse, to pump warm refrigerant through the outdoor coil and melt the ice off. That's the defrost cycle. It's a completely normal, engineered part of cold-climate operation, not a malfunction.

The noise comes from three things happening more or less at once: the reversing valve clunking as it switches direction, the compressor briefly working harder against a different pressure differential, and sometimes a burst of steam or dripping as the melted frost sheds off the coil. Some units also run the outdoor fan at a different speed or pause it during defrost, which changes the pitch of what you're hearing. None of that is subtle. It can sound like a distinctly different, rougher noise than the steady hum you're used to in summer cooling mode.

Why it's worse on some nights than others

Defrost frequency isn't fixed, it's a response to conditions. Cold, humid air with the temperature sitting somewhere between about 0°C and 5°C is actually the worst-case scenario for frost build-up, worse than genuinely freezing, dry air. That band is exactly what you get on a lot of southern Victorian or Tasmanian winter nights, and it's common through the Appalachian and Pacific Northwest US too. On those nights you might hear defrost cycling every 45 minutes to an hour. On a dry, properly cold night well below zero, the air holds less moisture and you might not hear it at all.

So if the noise seems to come and go with the weather rather than being constant, that's actually a good sign. It means the control logic is responding to real conditions rather than running on a dumb timer, which is how older or cheaper systems used to handle defrost, whether the coil needed it or not.

I'll say something a bit contrarian here: I think a lot of homeowners get more annoyance out of defrost noise than the actual decibel numbers on the spec sheet would suggest. It's not that it's loud in absolute terms, most cold-climate units are still well under 60 dB(A) at a few metres. It's that it's a sudden change in a sound you'd otherwise tuned out. Familiarity is doing a lot of the psychological work there, not physics.

Where the outdoor unit sits matters more in winter

This is the bit installers sometimes underweight. A unit mounted hard against a bedroom wall, or squeezed into a narrow side passage between two houses, will reflect and amplify defrost noise in a way it never does in summer cooling mode, because summer operation doesn't have that periodic clunk-and-fan-change pattern to bounce around. If you're speccing a new system, or you've had a run of complaints from a neighbour, the outdoor unit's placement relative to windows, bedrooms and boundary fences is worth more attention for winter noise than for summer noise. The same principle that governs where you'd never put a wind turbine, close to sleeping areas with hard reflective surfaces nearby, applies here at a much smaller scale.

If you're in the design stage, our piece on ducted vs split-system heat pumps covers how outdoor unit count and placement differ between the two configurations, which is directly relevant if defrost noise is a concern for a bedroom-adjacent install.

When defrost noise actually does signal a problem

None of this means every winter noise is fine. There are a few patterns worth flagging to your installer or an AS/NZS 3000-licensed technician rather than shrugging off:

A defrost cycle that runs constantly, say every ten to fifteen minutes rather than roughly hourly, usually points to a coil that's not clearing properly, low refrigerant charge, a failing sensor, or airflow being blocked by something like overgrown shrubs against the unit. A grinding or metallic noise, as opposed to the clunk-and-hum pattern described above, isn't normal defrost behaviour, that's mechanical wear, most likely in the fan motor bearing or compressor mounts. And a defrost cycle that never seems to end, where the unit just keeps running in reverse mode without going back to heating, suggests the reversing valve itself has failed to switch back, which will show up pretty quickly as the house not warming up at all.

The Australian Institute of Refrigeration, Air Conditioning and Heating (AIRAH) publishes technical guidance on defrost control logic if you want to go deeper on the engineering side, and it's a genuinely useful read if you're the type who wants the "why" rather than just the reassurance.

Cold-climate rated units and what changes

Not every heat pump handles this equally well. Units genuinely rated for cold climates, as opposed to standard models that technically still function below freezing but do so inefficiently, tend to use more sophisticated defrost algorithms that read coil temperature and humidity rather than running on a simple timer. That means fewer, shorter, better-timed defrost cycles, and less wasted energy reheating the house afterwards, since every defrost cycle briefly blows cool air inside before the reversing valve switches back. I've written more on what that rating actually guarantees on a spec sheet in our piece on cold-climate ratings, and it's worth reading before you assume "it runs in winter" and "it's built for winter" mean the same thing.

It also connects to the broader myth I keep running into, that heat pumps simply stop working below freezing. They don't, and I covered the mechanics of that in an earlier piece. Defrost cycling is actually part of why they keep working: it's the system actively managing the one real physical limitation cold air imposes on the refrigeration cycle.

Getting the sizing and install right in the first place

An oversized unit will short-cycle more, and short-cycling compounds with defrost cycling to create more frequent noise events overall, not fewer. This is one more reason proper load calculation matters, something I've banged on about before in our piece on Manual J and load calcs and in why oversizing quietly ruins comfort. A correctly sized system defrosts when it needs to and otherwise runs steadily; an oversized one cycles on and off more, which multiplies the number of transition events, including the noisy ones.

If you're vetting an installer for a new system, ask directly how they handle outdoor unit placement relative to bedrooms and how the model they're quoting manages defrost, demand response versus fixed timer. Our guide on vetting a heat pump installer has the fuller checklist, including licensing checks that matter for refrigerant work under the refrigerant handling licence requirements here in Australia.

The US Department of Energy's cold-climate heat pump technology page is a solid technical reference too, if you want the federal research-lab framing on how defrost control has improved over the last decade of product development.

Back to that Dandenong Ranges call. I checked the outdoor unit's mounting, confirmed the defrost cycle was running on a sensible interval given the night's conditions, roughly 40 minutes on a wet, hovering-around-3°C evening, and left her with a rough guide for what to listen for if things changed. Eighteen months on, no further calls. The tin-shed noise was just the system doing its job.

Tagged

Common questions

Should I turn my heat pump off if I hear defrost noise at night?
No, let it run. Turning it off mid-defrost can leave the coil partially iced, which makes the next cycle work harder and last longer. If the noise genuinely disrupts sleep, it's worth getting the outdoor unit placement reviewed rather than switching the system off.
Is defrost noise a sign my heat pump is undersized for the climate?
Not on its own. Defrost frequency depends mostly on outdoor humidity and temperature, not system capacity. A system that's genuinely undersized will show up as struggling to reach setpoint on cold days, not as noisier defrost cycles.
Do all heat pumps have a defrost cycle?
Any air-source heat pump running in heating mode with an outdoor coil exposed to cold, humid air needs some form of defrost logic below roughly 5°C ambient. Ground-source and water-source systems don't face the same issue since their source temperature stays more stable.
How long does a typical defrost cycle last?
Usually somewhere between two and ten minutes, depending on how much frost has built up and the system's defrost control method. Longer or more frequent cycles are worth investigating rather than assuming they're normal.
About the author
PN
Priya Nathan
Heat pumps & HVAC · Melbourne, AU

Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.

Mechanical engineering background; ex-HVAC design.

More from Priya Nathan