The buffer tank mistake that quietly wrecks heat pump efficiency
Three callouts in the same fortnight, all with the same complaint: "the heat pump short cycles and it's noisy and the bills are worse than the brochure promised." All three had buffer tanks. All three had the wrong size buffer tank. None of the homeowners had any idea that component even existed before I pointed at it on the wall.
A buffer tank is one of the least-discussed parts of a hydronic heat pump install, and it's one of the easiest things for a quote to get quietly wrong. Get the sizing right and it smooths out the system, protecting the compressor and keeping the unit running in its efficient middle band. Get it wrong, undersized especially, and you've built a heat pump that short cycles itself into an early grave while costing you more to run than the spec sheet ever suggested.
What a buffer tank is actually doing
On an air-to-water heat pump feeding hydronic radiators, underfloor heating or a fan coil, the compressor doesn't like being told to switch on and off every few minutes. Modern inverter-driven heat pumps modulate their output, but they still have a minimum run time and a minimum off time baked into the control logic for a reason: the refrigeration cycle needs to stabilise before it's doing useful, efficient work. Switch it on and off constantly and you're spending a disproportionate share of each cycle in the inefficient start-up phase, never getting to the flat, efficient part of the curve.
A buffer tank sits as thermal mass between the heat pump and the emitters. It stores a volume of heated water so the compressor can run a full cycle, park the extra heat in the tank, and switch off for a sensible stretch, rather than chasing a tiny, fast-responding zone valve that calls for heat in five-minute bursts. It's a hydraulic separator and a thermal flywheel in one. Done right, it's invisible. Done wrong, it's the single biggest reason a correctly sized heat pump still behaves badly.
Where the sizing actually goes wrong
The mistake isn't usually "no buffer tank." It's the wrong litres for the system's actual minimum run volume. Installers size buffer tanks off rules of thumb, litres per kW of heat pump capacity, lifted from a manufacturer's generic install manual that assumes a reasonably sized zone layout. That generic number doesn't know your house has four small zones each with their own thermostatic valve, or that your ground floor is one big open-plan zone that rarely calls for heat on its own.
Undersizing is the far more common failure. A tank too small for the system volume fills with heated water almost instantly once the compressor ramps up, the flow temperature satisfies the zone call within minutes, and the compressor is told to stop. Minutes later the zone cools and calls again. That's short cycling, and it's exactly the failure mode the buffer tank was installed to prevent in the first place, just with an undersized tank making it worse instead of better.
I've also seen the opposite mistake, a buffer tank sized generously for a system that's since been rezoned smaller, acting as a heat sink that the compressor has to keep topping up even when no room actually needs warmth. That's not dangerous, it's just wasteful, and it shows up as a flow temperature that never quite settles where the weather compensation curve says it should.
Why this gets missed on the quote
Most heat pump quotes focus on the box: capacity, COP, the brand. The hydraulic side, pipe diameters, pump head, buffer tank volume, often gets specified by whoever's doing the install on the day rather than calculated up front as part of a proper hydronic design. That's the same blind spot I've written about with duct and pipe run length being left off the quote entirely; the buffer tank is just another line item that gets a generic default instead of a calculation specific to your zoning layout.
A proper hydronic design calculates minimum system volume based on the heat pump's minimum modulation output and the system's lowest flow temperature, then works out how many litres of buffer are needed to give a sensible run time, typically aiming for at least eight to ten minutes of compressor run per cycle rather than two or three. That's a calculation, not a lookup table, and it depends on your specific zone count and valve type. If your installer hasn't asked how many zones you've got and what kind of valves are on them before quoting a buffer tank size, that's worth a direct question before signing.
The diagnostic that actually tells you
If you already have a heat pump installed and you suspect this is your problem, the test is straightforward: watch the compressor's run and off times over a typical heating call, not the thermostat display, the actual compressor status if your system logs it, or just listen and time it with a phone. A heat pump cycling on and off more than every ten minutes under normal thermostat setpoints, in anything but mild shoulder-season weather, is a decent sign something upstream of the compressor is forcing short cycles. It might be the buffer tank. It might also be oversizing of the unit itself, which I've covered separately, because oversized heat pumps and undersized buffers produce an almost identical symptom from two different causes.
The fix, if it is the buffer tank, usually isn't swapping the tank (though sometimes it is). More often an installer can adjust the minimum compressor run time in the controller settings, or add a low-loss header to decouple the primary and secondary circuits properly, which is a cheaper fix than ripping out a tank. I'd rather see a competent installer dial in the control logic for an existing undersized tank than replumb the whole plant room, and in my experience that's underused as a first step.
What this costs you if nobody fixes it
Short cycling isn't just annoying, it's a direct efficiency and longevity cost. Every start-up cycle on a refrigeration compressor consumes more current and produces less useful heat output per minute than steady-state running, because the compressor is working through oil return and refrigerant equalisation before it settles. A compressor doing twenty short cycles a day compared to six long ones is spending a measurably larger fraction of its runtime in that inefficient start-up window, and that shows up on your power bill as a COP that undershoots the number on the compliance plate even on a mild day. This is the same gap I covered in why the COP on the box isn't the COP you'll actually get, and a wrong buffer tank is one of the mechanical reasons that gap exists, not just a software or weather issue.
There's also a wear-and-tear cost that doesn't show up for a few years. Compressor manufacturers rate their units for a certain number of start cycles over their design life, and chronic short cycling burns through that allowance faster than steady operation. It's not usually enough to void a warranty outright, most manufacturers don't track cycle counts that granularly in the field, but it is enough to shorten the practical service life of the unit. I'd argue this is the part installers underplay most, because the failure shows up on someone else's service call, years down the track, not on the day of commissioning.
What to ask before you sign
If you're getting quotes for a new hydronic heat pump system, ask specifically whether a buffer tank or low-loss header is included, what volume it's sized at, and whether that number came from a calculation based on your zoning or a generic manufacturer default. Ask how many heating zones the system will have and what kind of valves control them, because that's the input the sizing depends on. If the installer can't answer in specifics, that's a reasonable prompt to get a second opinion, the same way I'd suggest checking what a heat pump installer's HVAC licence actually covers before committing to a hydronic job, since buffer tank and header sizing sits squarely inside the hydraulic design competency that licence is meant to certify.
It's also worth asking for the commissioning data once the system's running, specifically the flow temperature and compressor run times logged during the first heating season. Most decent commissioning paperwork includes this, and I've written before about how often that commissioning certificate gets skipped entirely. A buffer tank sized correctly should show up in that data as long, infrequent compressor cycles rather than the short, frequent pattern that signals trouble.
Manufacturer technical guidance from bodies like the Air-Conditioning, Heating, and Refrigeration Institute covers minimum system volume requirements for variable-speed heat pump compressors, and it's worth an installer referencing that rather than a rule of thumb scribbled on the back of a quote. The US Department of Energy's technical guidance on heat pump systems also touches on hydraulic separation, though it's written at a fairly general level and won't replace a proper site-specific calculation.
None of this is exotic engineering. It's a volume calculation against a minimum run-time target, checked against your actual zone count. The problem is almost nobody asks for it, and almost no quote itemises it, so it sits in the same blind spot as pipe runs and duct lengths: assumed, not calculated, until the compressor starts cycling every four minutes and somebody finally climbs into the plant room to find out why.
Frequently asked questions
Still a few things worth clearing up on this one.
— Priya Nathan, Heat Pumps & HVAC Writer, IceWarm
Common questions
- Do all hydronic heat pumps need a buffer tank?
- Not always. Some systems with enough inherent water volume in the pipework and emitters, or with a single large zone and no fast-acting thermostatic valves, can run fine without one. The need depends on your minimum system volume relative to the heat pump's lowest modulation output, which is a calculation your installer should be doing, not assuming.
- Can I retrofit a buffer tank to an existing heat pump that's short cycling?
- Usually yes, and it's often cheaper than it sounds if there's room in the plant area for the tank and associated pipework. Sometimes adjusting the compressor's minimum run time in the controller settings fixes the symptom without adding a tank at all, so it's worth asking an installer to check the control logic first.
- Is a bigger buffer tank always safer than a smaller one?
- No. Oversizing wastes energy by keeping a larger volume of water heated than the system actually needs, and it can slow the system's response to weather compensation changes. The goal is a volume matched to your minimum run-time target, not the biggest tank that fits.
- How do I know if short cycling is the buffer tank or the heat pump itself being oversized?
- Both produce similar symptoms, frequent on-off cycling and a worse-than-rated COP. The difference usually shows in the pattern: an oversized heat pump short cycles even on cold days because it's satisfying the whole house too fast, while a buffer tank problem tends to show up most on mild days when only a small zone is calling for heat. A commissioning technician checking flow temperature logs against outdoor temperature can usually tell the two apart.
Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.
Mechanical engineering background; ex-HVAC design.
More from Priya Nathan
- Why two identical heat pumps can sound totally different next doorSame unit, same decibel rating, wildly different noise complaints. The myth isn't the spec, it's where and how the outdoor unit gets placed.
- The design temperature mistake that skews every heat pump quoteMost heat pump quotes size off the wrong outdoor temperature. Here's why design temperature, not average winter temp, decides if your system actually keeps up.
- The humidity myth that throws off heat pump cooling estimatesHeat pump cooling quotes focus on temperature drop, but humidity removal is the part that actually decides comfort and running cost.
- Why "heat pumps don't work in the cold" is the wrong myth to worry aboutHeat pumps do work in the cold. The real myth is believing minimum operating temperature is the number that matters for your install.
- Vetting a refrigerant handling licence before heat pump work startsBefore a heat pump installer touches refrigerant lines, check their handling licence. Here's what the card actually proves and what it doesn't.
- Why a return-on-investment number for a heat pump rarely survives real lifeMost heat pump payback calculations use one winter's gas price and a brochure COP. Here's why the real payback period almost never matches the quote.