Vetting a heat pump installer's HVAC licence: what the card doesn't tell you
I was on a job in Reservoir last winter, standing in a garage with a homeowner who'd just paid a deposit to a bloke whose van said "Fully Licensed HVAC" in large friendly letters. She showed me his licence card, proudly, like it settled the matter. It didn't. The card confirmed he could legally handle refrigerant and wire up equipment. It told us absolutely nothing about whether he knew how to size a system for her 1970s brick veneer, or whether he'd done a single multi-head install before. Licensing and competence are two different questions, and almost nobody checks the second one.
This is the gap I want to walk through, because it's the one that costs people the most money down the track. Not the illegal cowboy stuff — most homeowners are smart enough to ask "are you licensed" these days. It's the legally-licensed-but-genuinely-not-good-at-this problem that quietly wrecks heat pump installs across Australia and the US.
What a licence actually certifies (and what it doesn't)
In Australia, the relevant trade licence — electrical for the circuit work, refrigerant handling licence for anyone touching the sealed system — proves someone has met a training and assessment bar and is legally allowed to do the work. It does not test whether they've ever run a Manual J equivalent load calculation, understood defrost behaviour in a cold climate, or correctly zoned a multi-head system. I've covered the refrigerant side specifically in our piece on refrigerant handling licence checks, and it's worth reading alongside this one because they overlap but aren't identical checks.
In the US, state licensing boards (and in some states, county-level contractor licensing) work similarly — a journeyman or master HVAC licence confirms code compliance competence, not manufacturer-specific commissioning skill for, say, a cold-climate-rated heat pump versus a standard unit. The Air Conditioning Contractors of America (ACCA) publishes the Manual J/S/D standards that proper sizing is supposed to follow, but there's no legal requirement that an installer actually use them. Plenty don't. I see the fallout constantly: a heat pump that's technically installed to code, wired correctly, refrigerant charged correctly, and still runs badly because nobody did the load calculation properly. We've written about exactly this failure mode in Manual J or gross feeling — it's the single most common root cause I see behind an oversized, short-cycling, uncomfortable system.
The manufacturer accreditation layer most people skip
Here's the bit that genuinely changes outcomes: manufacturer-specific training. Daikin, Mitsubishi Electric, Fujitsu and others run their own accreditation programmes on top of base trade licensing, and dealers who've actually completed them tend to install noticeably better. Ask directly: "are you an accredited dealer for this brand, and can I see the certificate number?" A legitimate installer has this answer ready. Someone who hedges — "oh yeah, we do heaps of these" — without a specific credential is giving you a sales answer, not a technical one. This matters more for ducted and multi-head systems than it does for a single split. The commissioning process, especially around refrigerant charge verification and zoning setup, is where manufacturer training actually shows up in the finished job. I'd go so far as to say that for anything above a single-zone split, I'd rather hire a licensed installer with the manufacturer accreditation than an unaccredited installer with ten more years on the tools. Experience without the specific training just means ten more years of the same workaround habits.
Insurance and workers' compensation: the boring check that saves you
Ask for proof of public liability insurance and, if they employ anyone, current workers' compensation cover. This feels like paperwork theatre until the day a ladder goes through a window or someone's back goes out on your roof and there's no cover. A reputable outfit has these documents ready within a day, usually on file at the office. If a quote arrives with no ABN, no business name matching the invoice, and a reluctance to provide insurance certificates, that's your answer before you've even discussed the equipment. The equivalent in the US is a current contractor's licence number plus general liability insurance, verifiable through your state licensing board's public lookup tool — most states, including Texas and New York, run searchable online registries. Takes two minutes. Do it before the deposit, not after.
Red flags I've actually seen on real jobs
A few patterns repeat often enough that they're worth naming directly rather than hedging about "some installers." The quote that skips the load calculation entirely and jumps straight to "you'll need a 7kW unit for a house this size" is one. Sizing by square metreage alone, without asking about insulation, window orientation, or ceiling height, is a guess dressed up as expertise — and it's exactly the oversizing problem covered in why oversizing quietly ruins comfort and running costs. The second is a quote with no commissioning certificate mentioned at all. A proper job finishes with documented superheat/subcooling readings, airflow verification and a signed commissioning sheet — not just a working unit and an invoice. We've detailed exactly what that paperwork should look like in the commissioning certificate checklist, and I'd hold any quote to that standard before signing. Third: circuit sizing glossed over in one line of the quote, or not mentioned at all. This is a surprisingly common and avoidable failure — see the circuit sizing mistake that trips installs before day one for how often this bites people who assumed the electrician and the HVAC installer were talking to each other. Sometimes they aren't, and the gap shows up as a failed inspection or a unit that can't actually draw what it needs. Fourth, and this one's subtle: an installer who can't explain COP in plain terms when you ask about running costs. They don't need to recite the thermodynamics, but if they can't tell you honestly that the number on the box isn't the number you'll get in your climate — see the COP number on the box isn't the COP you'll get — that's a installer who's selling spec sheets, not systems.
What to actually ask before you sign anything
Ask for the refrigerant handling licence number and the trade licence number separately, and check both against your state or territory's public register — in Australia that's typically the state fair trading or consumer affairs licence lookup; in the US it's your state contractor licensing board. Ask whether a Manual J (or AS/NZS 4859.1-aligned load calculation locally) will be performed and documented, not estimated. Ask for the manufacturer accreditation certificate if it's a ducted or multi-head system. Ask what the commissioning paperwork will include and request a copy in advance, in writing. None of this is unreasonable, and a good installer will answer without flinching because they do this for every job anyway. I'll be blunt: if a tradesperson treats these questions as an insult to their experience rather than standard due diligence, that's information too. The installers I trust most answer faster, not slower, when pressed on paperwork.
Where this fits with solar and battery vetting
If you're also getting solar or battery quotes at the same time — common enough, since a heat pump upgrade often triggers a broader electrification conversation — the vetting logic is similar but not identical. Our guide on how to choose a solar installer without getting burned covers the solar-specific checks, and if a battery's in the mix, who signs what between a battery electrician and an accredited installer is worth reading before you commit to one contractor doing everything. It's common for one tradesperson to be licensed for part of a combined job and subcontracting the rest, which is fine, but you want to know who's actually accountable for each signature on the commissioning paperwork. The Clean Energy Council in Australia and NABCEP in the US both maintain installer accreditation directories worth cross-checking against whatever credentials are quoted to you — it takes minutes and catches more than you'd expect.
Back in that Reservoir garage, the homeowner ended up calling the manufacturer's dealer line directly and asking for an accredited installer in her postcode. Different quote, slightly higher price, noticeably better commissioning sheet. The licence card hadn't changed anything about her decision in the end — what changed it was asking the next three questions.
— Priya Nathan, Heat Pumps & HVAC, IceWarm
Common questions
- Is a licensed HVAC installer automatically qualified to install a heat pump specifically?
- Not necessarily. A trade or refrigerant handling licence confirms they're legally allowed to do the work and have passed a competency bar, but it doesn't test brand-specific commissioning skill or whether they'll actually run a proper load calculation rather than guessing on size.
- How do I verify an installer's licence is real and current?
- In Australia, check your state or territory's fair trading / consumer affairs licence lookup tool using the licence number on their quote. In the US, your state contractor licensing board runs a searchable public registry — most, including Texas and New York, have this online.
- Does manufacturer accreditation actually matter, or is it just marketing?
- It matters most for ducted and multi-head systems, where commissioning and zoning setup genuinely differ between accredited and unaccredited installers. For a single split system it's less critical, but I'd still ask for the certificate number on any job above entry-level.
- What's the single biggest red flag in a heat pump quote?
- A quote that sizes the unit by floor area alone with no mention of a load calculation, orientation, insulation level or window area. That's a guess, and it's the most common root cause of oversized, uncomfortable, short-cycling systems I see.
Priya covers heat pump heating, cooling and hot water systems — sizing, running costs, and what actually changes between an Australian and a US install.
Mechanical engineering background; ex-HVAC design.
More from Priya Nathan
- The design temperature mistake that skews every heat pump quoteMost heat pump quotes size off the wrong outdoor temperature. Here's why design temperature, not average winter temp, decides if your system actually keeps up.
- The humidity myth that throws off heat pump cooling estimatesHeat pump cooling quotes focus on temperature drop, but humidity removal is the part that actually decides comfort and running cost.
- Why "heat pumps don't work in the cold" is the wrong myth to worry aboutHeat pumps do work in the cold. The real myth is believing minimum operating temperature is the number that matters for your install.
- Vetting a refrigerant handling licence before heat pump work startsBefore a heat pump installer touches refrigerant lines, check their handling licence. Here's what the card actually proves and what it doesn't.
- Why a return-on-investment number for a heat pump rarely survives real lifeMost heat pump payback calculations use one winter's gas price and a brochure COP. Here's why the real payback period almost never matches the quote.
- Vetting a ducted heat pump installer: the warranty registration trapMost heat pump warranties need the installer to register the system within days. Miss that step and the manufacturer owes you nothing.