Vetting a render or external cladding installer: licences and red flags
I got a call last month from a reader in Ocean Grove whose acrylic render had started bubbling along the south wall, eighteen months after a "full house re-render." No cavity, no drainage detail, insulation behind it already damp. The render itself wasn't the problem. What was underneath it, and who signed off on it, was. This is the trade homeowners think least about when they're doing an energy retrofit, and it's arguably one of the most consequential — because whatever cladding or render system goes over your wall decides whether your insulation stays dry for the next twenty years or turns into a wet blanket inside your studs.
I spend most of my time looking at insulation, glazing and the numbers that come out of a NatHERS or HERS assessment, but none of that holds up if the skin of the building is done badly. A rating tells you what the envelope should achieve on paper. It says nothing about whether the cladding installer actually understood how water moves behind their product.
Why this trade gets skipped in the vetting conversation
Everyone vets electricians and plumbers because there's an obvious licence category and an obvious safety story if it goes wrong. Cladding and render sit in a murkier spot. In most Australian states the work falls under general building licensing rather than a single dedicated trade licence, and the regulatory line between "who can legally do this" and "who is actually competent at this" is wider than for gas or electrical work. That gap is where problems live.
It's also a trade where the failure mode is slow. A bad electrical job trips a switch immediately. A bad cladding job takes twelve to thirty-six months to show up as bubbling paint, staining, or a musty smell in a bedroom that backs onto the affected wall. By the time the homeowner notices, the installer has moved three suburbs over and the warranty conversation is a fight.
The licence and registration checks that actually matter
Start with the state building licence, not a trade card. In most states, render and cladding installation over a certain contract value requires the tradesperson (or the business) to hold a registered building practitioner licence in the relevant class — often something like "wall and ceiling lining" or a broader "building work" category depending on the jurisdiction. Ask for the licence number and check it against your state's public building practitioner register before you sign anything. This takes five minutes and it's the single most skipped step I hear about.
Second, ask which cladding or render system they're installing and whether they hold current manufacturer accreditation for it. This matters more here than in most trades, because most proprietary render and lightweight cladding systems (EIFS-style acrylic systems, fibre cement panel systems, certain weatherboard composites) only carry a manufacturer warranty if the installer is on the accredited applicator list. An unaccredited install might look identical on day one and void the product warranty entirely on day one too. I'd want to see the accreditation certificate, not just hear "yeah I do heaps of that."
Third, for anything involving structural fixing into timber or steel framing, check they're working to the relevant timber framing code — in Australia that's the National Construction Code and AS 1684 for fixing details. Ask specifically how they're fixing into the frame and what fastener spacing they're using. A trade who can't answer that without checking their phone hasn't done enough of this work.
The red flags that show up before the contract
The quote itself tells you a lot. A quote that lists "render house, $X" with no breakdown of cavity system, flashing details, control joints or weep holes is a quote from someone who either doesn't plan for those details or isn't going to charge for them, which usually means they won't be done. Get a line-item breakdown. If they push back on that, that's the red flag, not the request.
Ask what happens at every penetration: window reveals, meter boxes, downpipe brackets, hose taps. These are the spots where water gets in on ninety percent of failed jobs I've heard about from readers and from builders I trust. If the answer is vague — "we'll flash it up as we go" — that's not a plan, that's an intention.
Watch for the trade who wants full payment upfront or a deposit well above the standard 10-to-20 percent range typical for domestic building contracts in most states. Large upfront deposits are one of the clearest signals of cash-flow-dependent operators who are financing last month's job with this month's deposit. It's not proof of anything on its own, but combined with a vague scope it's a pattern worth walking away from.
Insurance is non-negotiable. Ask for a certificate of currency for public liability and, where the job value requires it, home warranty insurance. Don't accept "I'll email it to you" as a substitute for actually seeing it before work starts.
What good cladding practice actually looks like on site
I always tell readers doing an insulation or glazing upgrade to walk the site once mid-job if they can. On a cladding or render job, three things separate the trades who know what they're doing from the ones who don't.
First, a drained and vented cavity behind the cladding or render, not a direct-fixed system on a masonry veneer or timber frame without one, unless the specific product is genuinely designed and warranted for direct fixing in your climate zone. Second, flashings that are installed before the cladding goes on, not caulked in afterwards as an afterthought. Sealant is not a flashing detail; it's a maintenance item that will eventually fail. Third, a weep hole or drainage path at the base of every cavity so any water that does get behind the cladding has somewhere to go.
This is the same logic that runs through a good air sealing before insulation job — sequence and detailing matter more than the headline material. A premium cladding product installed with no cavity behaves worse over time than a basic product installed with correct drainage. I'd rather see a plain fibre cement board with proper flashings than a fancy acrylic finish with none.
Certifications worth asking for by name
Beyond the state licence, ask for three specific documents. The manufacturer's system warranty certificate, issued in your name once the job is complete — not a generic brochure. A compliance certificate or certificate of conformance referencing the relevant standard for weatherproofing, which in Australia typically ties back to the deemed-to-satisfy provisions of the National Construction Code. And, if the job triggers a building permit in your council area, the final inspection sign-off from the relevant building surveyor.
If the trade tells you cladding work "doesn't need a permit," check that yourself with your local council rather than taking their word for it. Permit requirements vary by job scope, cladding type and whether structural elements are altered, and I've seen this used as an excuse to skip inspections that would have caught a bad flashing detail.
One thing I'll say plainly, because it's a slightly unpopular opinion among some installers I've spoken with: I think homeowners over-trust "we've been doing this for twenty years" as a stand-in for licence and accreditation checks. Longevity in a trade tells you they've survived, not that every job they've done in that time was done to spec. Ask for the paperwork regardless of how long they've been at it.
How this connects back to your energy performance
A wet wall doesn't just rot the cavity. Moisture in bulk or reflective insulation drops its performance meaningfully, and once insulation is wet it usually needs full replacement rather than drying out in place. That has a direct line back to the R-values your NatHERS or HERS certificate assumed the wall would hold, and to whatever star rating the house was designed against. A failed cladding job can undo years of careful envelope work and turn a well-rated house into one that's quietly underperforming its rating within a couple of winters.
If you're doing render or cladding as part of a broader retrofit alongside new glazing or insulation upgrades, sequence it properly and get each trade's work inspected before the next one covers it up. That's the same principle I push on with window and glazing installers and with insulation installers: check the licence, check the accreditation for the specific product, and get eyes on the detailing before it disappears behind the finish coat. For general guidance on choosing any home-energy trade, our how to choose a solar installer piece covers vetting principles that apply more broadly than just solar, and the trades hub has the rest of our licensing checklists by category.
The Ocean Grove render job is getting redone properly this time, with a drained cavity and a builder who pulled his licence number up on his phone before I asked. That's roughly the bar. It shouldn't be a high one.
— Ben Sorensen, Green Building Writer, IceWarm
Common questions
- Does render or cladding installation always require a licensed builder?
- In most Australian states, yes above a certain contract value threshold, and often regardless of value for structural cladding work. Check your state's building practitioner register for the specific licence class, such as wall and ceiling lining or a broader building work category, and confirm the number before signing a contract.
- What's the difference between a state licence and manufacturer accreditation?
- The state licence confirms someone is legally allowed to do building work in that category. Manufacturer accreditation confirms they've been trained on a specific proprietary system and that the product warranty will actually apply to their installation. You need both, not one or the other.
- Can wet insulation behind cladding be dried out instead of replaced?
- Generally no, once bulk or reflective insulation has been saturated for any length of time it loses R-value permanently and usually needs replacing along with any damaged framing, which is one of the reasons a poor cladding installation is expensive to fix properly.
- Is a large upfront deposit always a red flag?
- Not always, but a deposit well above the standard 10 to 20 percent range typical for domestic contracts, combined with a vague scope of works, is a pattern worth questioning rather than a definite scam on its own.
Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.
Building-certification background (NatHERS-adjacent).
More from Ben Sorensen
- Why a NatHERS or HERS rating can change without touching the buildA NatHERS or HERS rating can shift star bands when software updates, climate files get revised, or rules change — even if your house hasn't.
- Why your NatHERS or HERS rating ignores your floor coveringsCarpet, tile and polished concrete all score the same in a NatHERS or HERS model, even though they feel wildly different underfoot and change how your heating actually performs.
- Vetting an insulation installer: the R-value receipt nobody asks forInsulation installers rarely need a specific trade licence, which is exactly why the paperwork trail matters more than the handshake.
- Why your NatHERS or HERS rating never touches your thermal bridgesA NatHERS or HERS rating models your walls as flat layers, which means steel studs, balcony slabs and window reveals rarely get the credit (or blame) they deserve.
- Why your NatHERS or HERS rating never checks your orientation on siteYour NatHERS or HERS star rating locks in orientation at design stage, but nobody re-checks it once the slab is poured the wrong way round.
- Vetting a window glazier for new-build glazing: what to checkBefore a glazier touches your new-build windows, check the licence, the AS 2047 compliance paperwork and the install method. Here's what actually matters.