Does a NatHERS or HERS rating ever check your insulation installation?
I had a builder ring me last month, genuinely confused. His house had just scraped a 7-star NatHERS rating on paper, but the insulation batts in the roof were sitting squashed under a pile of sarking offcuts in one corner, and gappy as a missing tooth along the top plate in another. "How did it still pass?" he asked. The honest answer: the rating never checked. It assumed.
That's the gap I want to walk through today, because it trips up more homeowners than almost anything else in the certification process. People treat a NatHERS or HERS certificate as proof the insulation was installed properly. It isn't that. It's a modelled prediction based on what the plans say should be there, and in most jurisdictions, nobody from the rating process ever goes back up the ladder to confirm the batts actually ended up where the drawings said they would.
What the rating models vs what gets built
A NatHERS assessment (or a HERS rating in the US) takes a 3D model of your house, applies a standardised climate file, and calculates expected heating and cooling loads based on the specifications on the plans — wall construction, glazing performance, and yes, insulation R-values per element. I've covered how those climate file assumptions work in more detail elsewhere, but the short version matters here too: the software assumes the R-value on the drawing is the R-value in the wall.
It isn't always. R-value ratings are measured on insulation batts installed in laboratory conditions, compressed to the correct thickness, with no gaps, no compression, no thermal bridging. Real roofs have downlights, services, and tradies in a hurry. A batt compressed to half its design thickness loses a meaningful chunk of its rated performance, not a little, a lot — R-value scales roughly with thickness for most bulk insulation products, so squashing a 90mm batt to 45mm under a cable tray isn't a cosmetic issue.
The inspection that (mostly) doesn't happen
Here's the part that surprises most people: the assessor who produces your NatHERS certificate typically never sets foot on site during construction. The rating is desktop-based, done from architectural drawings before a single stud goes up. I wrote previously about what an assessor actually checks on site for a related piece, and the reality is that "on site" visits, where they happen at all, are usually tied to a different process entirely — a building surveyor's mandatory inspection stages, or a council's insulation certificate requirement, not the energy rating itself.
In Victoria and New South Wales, building surveyors are required to inspect insulation before it's covered by plasterboard, under the National Construction Code's insulation installation provisions. That's a real checkpoint. But it's a pass/fail compliance check against a minimum, not a verification that the specific R-value modelled in your NatHERS assessment was actually delivered, batt by batt, bay by bay. Two houses can both "pass" that inspection while one has noticeably better continuity of coverage than the other.
I'll be blunt about something here: I think this is the single weakest link in the whole ratings chain, weaker than the orientation assumptions or the occupancy modelling I've written about before. A design tool with no build-stage verification loop is only ever as good as the trade standing on the ladder that day.
Why this matters more for insulation than glazing
Window performance is comparatively easy to audit after the fact — the glazing unit has a stamp, the frame has a certification, and a site visit with a tape measure can confirm what's actually installed matches the schedule. Bulk insulation is different. Once the plasterboard goes up, it's invisible. Nobody is pulling back sheets to check compression or gaps unless there's a specific complaint or a thermal imaging audit commissioned separately.
That's part of why I keep steering people toward a blower door and thermal camera assessment as a genuinely useful add-on, separate from the certificate. It's the one process that actually looks at what's behind the plaster rather than what's on the drawing. If you're commissioning one, our piece on vetting a blower door and thermal imaging auditor covers what to ask before you pay for the report.
Thermal bridging is the other half of this problem, and it rarely shows up anywhere near the rating. Timber studs, steel framing members, and junctions where insulation can't physically continue, around services penetrations, at wall-to-ceiling junctions, behind recessed downlights, all create localised heat loss paths that the standard NatHERS software doesn't model in fine detail. I touched on this in an earlier piece about the small stuff that bites you, and insulation installation quality sits right in that same blind spot.
What a good installer actually does differently
I've watched enough installs now to pick the good crews quickly. They cut batts to fit around services rather than stuffing them in regardless. They don't compress product to make it fit a tighter cavity. They fill gaps around downlights with appropriate IC-rated covers rather than leaving a hole in the blanket. None of that shows up on a certificate. All of it shows up on an energy bill, eventually.
If you're building or renovating, the practical move is to treat the insulation install as its own checkpoint, independent of whatever rating process is running in parallel. Ask your builder who is checking compression and continuity before the plaster stage, not after. If you're hiring the trade directly, our guide to vetting an insulation installer's licence covers what credentials and site practices to look for before signing. It's a cheap insurance policy against exactly the squashed-batts scenario the builder described to me.
For homes already built, a thermal imaging walkthrough on a cold morning (ideally with a decent temperature differential between inside and outside, the Clean Energy Council's guidance on home energy assessments has useful context on timing) will show cold spots where insulation has slumped, gapped, or was never fitted in the first place. It's a cheap diagnostic relative to the energy wasted over a decade of a poorly insulated ceiling.
Does a star rating even reflect reality after handover?
Strictly, no, and this is worth sitting with. The certificate you're handed at settlement reflects the house as drawn, not the house as built. If variations happened during construction, a cheaper insulation product substituted, a different batt thickness used to fit a tighter truss cavity, that model was never updated to match. The U.S. Department of Energy's guidance on home energy assessments is clear that a HERS Index Score reflects modelled performance against the as-designed specification, and actual field verification requirements vary significantly by which certification pathway and which jurisdiction's building code is in play.
This is a big part of why I tell people a rating is a design input, not a build receipt, a theme my colleague has covered in more depth in why the rating is a design tool, not a build receipt. The certificate tells you what should happen if everything specified gets installed as specified. It can't tell you whether it did.
What I actually tell clients to check
Walk the roof space before handover if you can, torch in hand, and look for daylight gaps, compressed sections near services, and any batt that's visibly slipped out of its bay. It takes twenty minutes and most builders won't object to a client doing a final walkthrough. Ask for photos of the insulation install before the ceiling went up, plenty of good builders already take these for their own records and will happily share them.
And don't assume a strong star rating number means the thermal envelope performs as modelled. It means the design, on paper, should perform that way if construction matched the drawings exactly. Whether it did is a separate question entirely, one the certificate was never built to answer.
— Ben Sorensen, Green Building Writer, IceWarm
Common questions
- Does the assessor who issues my NatHERS certificate inspect the insulation on site?
- Almost never. NatHERS assessments are desktop-based, calculated from architectural drawings before construction. Site inspections of insulation, where they happen, are typically a separate building surveyor requirement under the National Construction Code, not part of the energy rating process itself.
- Can compressed insulation really affect my star rating in practice, even if the certificate says otherwise?
- Yes, in terms of actual thermal performance, even though the certificate itself won't change. Compressing a batt reduces its effective R-value roughly in proportion to how much thinner it ends up, so a squashed batt in a roof cavity can underperform its rated value by a significant margin without anyone noticing.
- Is a thermal imaging audit worth paying for separately from the NatHERS process?
- I think so, particularly for an existing home or just before handover on a new build. It's the only common assessment type that actually looks at what's behind the plasterboard rather than relying on the as-designed specification.
- Who is actually responsible for checking insulation quality during a build?
- In most Australian states, the building surveyor signs off on insulation at a mandatory inspection stage before the walls and ceiling are closed in, under the National Construction Code. That's a compliance check against a minimum standard, not a verification against your specific NatHERS model.
Ben covers insulation, glazing and home energy ratings — the building-envelope work that decides how hard every other system has to work.
Building-certification background (NatHERS-adjacent).
More from Ben Sorensen
- Why a NatHERS or HERS rating can change without touching the buildA NatHERS or HERS rating can shift star bands when software updates, climate files get revised, or rules change — even if your house hasn't.
- Why your NatHERS or HERS rating ignores your floor coveringsCarpet, tile and polished concrete all score the same in a NatHERS or HERS model, even though they feel wildly different underfoot and change how your heating actually performs.
- Vetting an insulation installer: the R-value receipt nobody asks forInsulation installers rarely need a specific trade licence, which is exactly why the paperwork trail matters more than the handshake.
- Why your NatHERS or HERS rating never touches your thermal bridgesA NatHERS or HERS rating models your walls as flat layers, which means steel studs, balcony slabs and window reveals rarely get the credit (or blame) they deserve.
- Why your NatHERS or HERS rating never checks your orientation on siteYour NatHERS or HERS star rating locks in orientation at design stage, but nobody re-checks it once the slab is poured the wrong way round.
- Vetting a window glazier for new-build glazing: what to checkBefore a glazier touches your new-build windows, check the licence, the AS 2047 compliance paperwork and the install method. Here's what actually matters.